Introduction to Heat Transfer
6th Edition
ISBN: 9780470501962
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 3, Problem 3.7P
To determine
The value of heat gain per unit surface area.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Q1/ Consider a large plane wall of thickness L=0.03 m. The wall surface at x =0
is insulated, while the surface at x =L is maintained at a temperature of 30°C. The
thermal conductivity of the wall is k=25 W/m °C, and heat is generated in the
wall at a rate of g = 9oe0.5x/L W/m³ Where g, = 8 x 10 W /m². Assuming
steady one-dimensional heat transfer, (a) express the differential equation and the
boundary conditions for heat conduction through the wall, (b) obtain a relation for
the variation of temperature in the wall by solving the differential equation, and (c)
determine the temperature of the insulated surface of the wall.
1. Find the heat transfer per unit area through the composite wall in Figure below. Assume
one-dimensional heat flow.
k₁= 150 W/m-°C
kg = 30
kc=50
A = 0.1 m²
kD=70
B
AB=AD
D
7.5 cm
T=370°C
2.5 cm
H
4
5.0 cm
T = 66°C
Please i need hand written solution on pages in 60 mins i will give you positive feedback
Chapter 3 Solutions
Introduction to Heat Transfer
Ch. 3 - Consider the plane wall of Figure 3.1, separating...Ch. 3 - A new building to be located in a cold climate is...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - The rear window of an automobile is defogged by...Ch. 3 - A dormitory at a large university, built 50 years...Ch. 3 - In a manufacturing process, a transparent film is...Ch. 3 - Prob. 3.7PCh. 3 - A t=10-mm-thick horizontal layer of water has a...Ch. 3 - Prob. 3.9PCh. 3 - The wind chill, which is experienced on a cold,...
Ch. 3 - Prob. 3.11PCh. 3 - A thermopane window consists of two pieces of...Ch. 3 - A house has a composite wall of wood, fiberglass...Ch. 3 - Prob. 3.14PCh. 3 - Prob. 3.15PCh. 3 - Work Problem 3.15 assuming surfaces parallel to...Ch. 3 - Consider the oven of Problem 1.54. The walls of...Ch. 3 - The composite wall of an oven consists of three...Ch. 3 - The wall of a drying oven is constructed by...Ch. 3 - The t=4-mm-thick glass windows of an...Ch. 3 - Prob. 3.21PCh. 3 - In the design of buildings, energy conservation...Ch. 3 - Prob. 3.23PCh. 3 - Prob. 3.24PCh. 3 - Prob. 3.25PCh. 3 - A composite wall separates combustion gases at...Ch. 3 - Prob. 3.27PCh. 3 - Prob. 3.28PCh. 3 - Prob. 3.29PCh. 3 - The performance of gas turbine engines may...Ch. 3 - A commercial grade cubical freezer, 3 m on a...Ch. 3 - Prob. 3.32PCh. 3 - Prob. 3.33PCh. 3 - Prob. 3.34PCh. 3 - A batt of glass fiber insulation is of density...Ch. 3 - Air usually constitutes up to half of the volume...Ch. 3 - Prob. 3.37PCh. 3 - Prob. 3.38PCh. 3 - The diagram shows a conical section fabricatedfrom...Ch. 3 - Prob. 3.40PCh. 3 - From Figure 2.5 it is evident that, over a wide...Ch. 3 - Consider a tube wall of inner and outer radii ri...Ch. 3 - Prob. 3.43PCh. 3 - Prob. 3.44PCh. 3 - Prob. 3.45PCh. 3 - Prob. 3.46PCh. 3 - To maximize production and minimize pumping...Ch. 3 - A thin electrical heater is wrapped around the...Ch. 3 - Prob. 3.50PCh. 3 - Prob. 3.51PCh. 3 - Prob. 3.52PCh. 3 - A wire of diameter D=2mm and uniform temperatureT...Ch. 3 - Prob. 3.54PCh. 3 - Electric current flows through a long rod...Ch. 3 - Prob. 3.56PCh. 3 - A long, highly polished aluminum rod of diameter...Ch. 3 - Prob. 3.58PCh. 3 - Prob. 3.59PCh. 3 - Prob. 3.60PCh. 3 - Prob. 3.61PCh. 3 - Prob. 3.62PCh. 3 - Consider the series solution, Equation 5.42, for...Ch. 3 - Prob. 3.64PCh. 3 - Copper-coated, epoxy-filled fiberglass circuit...Ch. 3 - Prob. 3.66PCh. 3 - A constant-property, one-dimensional Plane slab of...Ch. 3 - Referring to the semiconductor processing tool of...Ch. 3 - Prob. 3.69PCh. 3 - Prob. 3.70PCh. 3 - Prob. 3.71PCh. 3 - The 150-mm-thick wall of a gas-fired furnace is...Ch. 3 - Steel is sequentially heated and cooled (annealed)...Ch. 3 - Prob. 3.74PCh. 3 - Prob. 3.75PCh. 3 - Prob. 3.76PCh. 3 - Prob. 3.77PCh. 3 - Prob. 3.78PCh. 3 - The strength and stability of tires may be...Ch. 3 - Prob. 3.80PCh. 3 - Prob. 3.81PCh. 3 - A long rod of 60-mm diameter and thermophysical...Ch. 3 - A long cylinder of 30-min diameter, initially at a...Ch. 3 - Work Problem 5.47 for a cylinder of radius r0 and...Ch. 3 - Prob. 3.85PCh. 3 - Prob. 3.86PCh. 3 - Prob. 3.87PCh. 3 - Prob. 3.88PCh. 3 - Prob. 3.89PCh. 3 - Prob. 3.90PCh. 3 - Prob. 3.91PCh. 3 - Prob. 3.92PCh. 3 - In Section 5.2 we noted that the value of the Biot...Ch. 3 - Prob. 3.94PCh. 3 - Prob. 3.95PCh. 3 - Prob. 3.96PCh. 3 - Prob. 3.97PCh. 3 - Prob. 3.98PCh. 3 - Work Problem 5.47 for the case of a sphere of...Ch. 3 - Prob. 3.100PCh. 3 - Prob. 3.101PCh. 3 - Prob. 3.102PCh. 3 - Prob. 3.103PCh. 3 - Consider the plane wall of thickness 2L, the...Ch. 3 - Problem 4.9 addressed radioactive wastes stored...Ch. 3 - Prob. 3.106PCh. 3 - Prob. 3.107PCh. 3 - Prob. 3.108PCh. 3 - Prob. 3.109PCh. 3 - Prob. 3.110PCh. 3 - A one-dimensional slab of thickness 2L is...Ch. 3 - Prob. 3.112PCh. 3 - Prob. 3.113PCh. 3 - Prob. 3.114PCh. 3 - Prob. 3.115PCh. 3 - Derive the transient, two-dimensional...Ch. 3 - Prob. 3.117PCh. 3 - Prob. 3.118PCh. 3 - Prob. 3.119PCh. 3 - Prob. 3.120PCh. 3 - Prob. 3.121PCh. 3 - Prob. 3.122PCh. 3 - Consider two plates, A and B, that are each...Ch. 3 - Consider the fuel element of Example 5.11, which...Ch. 3 - Prob. 3.125PCh. 3 - Prob. 3.126PCh. 3 - Prob. 3.127PCh. 3 - Prob. 3.128PCh. 3 - Prob. 3.129PCh. 3 - Consider the thick slab of copper in Example 5.12,...Ch. 3 - In Section 5.5, the one-term approximation to the...Ch. 3 - Thermal energy storage systems commonly involve a...Ch. 3 - Prob. 3.133PCh. 3 - Prob. 3.134PCh. 3 - Prob. 3.135PCh. 3 - A tantalum rod of diameter 3 mm and length 120 mm...Ch. 3 - A support rod k=15W/mK,=4.0106m2/s of diameter...Ch. 3 - Prob. 3.138PCh. 3 - Prob. 3.139PCh. 3 - A thin circular disk is subjected to induction...Ch. 3 - An electrical cable, experiencing uniform...Ch. 3 - Prob. 3.142PCh. 3 - Prob. 3.145PCh. 3 - Consider the fuel element of Example 5.11, which...Ch. 3 - Prob. 3.147PCh. 3 - Prob. 3.148PCh. 3 - Prob. 3.149PCh. 3 - Prob. 3.150PCh. 3 - In a manufacturing process, stainless steel...Ch. 3 - Prob. 3.153PCh. 3 - Carbon steel (AISI 1010) shafts of 0.1-m diameter...Ch. 3 - A thermal energy storage unit consists of a large...Ch. 3 - Small spherical particles of diameter D=50m...Ch. 3 - A spherical vessel used as a reactor for producing...Ch. 3 - Batch processes are often used in chemical and...Ch. 3 - Consider a thin electrical heater attached to a...Ch. 3 - An electronic device, such as a power transistor...Ch. 3 - Prob. 3.161PCh. 3 - In a material processing experiment conducted...Ch. 3 - Prob. 3.165PCh. 3 - Prob. 3.166PCh. 3 - Prob. 3.167PCh. 3 - Prob. 3.168PCh. 3 - Prob. 3.173PCh. 3 - Prob. 3.174PCh. 3 - Prob. 3.175PCh. 3 - Prob. 3.176PCh. 3 - Prob. 3.177P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q1. Consider a plane wall (thermal conductivity, k = 0.8 W/mK, and thickness, fb1 = 100 mm) of a house as shown in Fig. Q1(a). The outer surface of the wall is exposed to solar radiation and has an absorptivity of a = 0.5 for solar energy, or=600 W/m². The temperature of the interior of the house is maintained at T1 = 25 °C, while the ambient air temperature outside remains at T2 = 5 °C. The sky, the ground and the surfaces of the surrounding structures at this location can be modelled as a surface at an effective temperature of Tsky = 255 K for radiation exchange on the outer surface. The radiation exchange inside the house is negligible. The convection heat transfer coefficients on the inner and the outer surfaces of the wall are h₁ = 5 W/m²-K and /1₂ = 20 W/m².K, respectively. The emissivity of the outer surface is = 0.9. T1 = 25 °C Ţ₁ Too1 = 25 °C T₁ k 100 mm Fig. Q1(a) Assuming the heat transfer through the wall to be steady and one-dimensional: (a) Solve the steady 1D heat…arrow_forward= Consider a large plane wall of thickness L=0.3 m, thermal conductivity k = 2.5 W/m.K, and surface area A = 12 m². The left side of the wall at x=0 is subjected to a net heat flux of ɖo = 700 W/m² while the temperature at that surface is measured to be T₁ = 80°C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary equations for steady one- dimensional heat conduction through the wall, (b) obtain a relation for the variation of the temperature in the wall by solving the differential equation, and (c) evaluate the temperature of the right surface of the wall at x=L. Ti до L Xarrow_forwardQ1: Water at 80 oC is pumped through 100 m of stainless steel pipe, k=16 W/m.K of inner and outer radius 47 mm and 50 mm respectively. The heat transfer coefficient due to water is 2000 W/m2.K. The outer surface of the pipe loses heat by convection to air at 20 oC and the heat transfer coefficient is 200 W/m2.K. Calculate the heat flow through the pipe. Also calculate the heat flow through the pipe when a layer of insulation, k=0.1 W/m.K and 50 mm radial thickness is .wrapped around the pipearrow_forward
- Q1: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C, and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m2 C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans : (c) 6030 Warrow_forwardFind the heat transfer per unit area through the composite wall. Assume one-dimensional heat flowarrow_forwardHow long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.arrow_forward
- 2. A steel plate of k=50W/mK and thickness 10cm passes a heat flux by conduction of 25kW/m2. If the temperature of hot surface of plate is 100 C, then what is the temperature of the cooler side of plate? 1. 30 C 2. 40 C 3. 50 C 4. 60 Carrow_forwardQ2. Steam pumped through a long- insulated pipe at a temperature of T= 500 K and provides a convection coefficient of h, = 100 W/m?K at the inner surface of the pipe. The inner and outer radius of the pipe and insulation material are r1 = 10, r2 = 12 and r3 = 17 cm, respectively. The thermal conductivity of the pipe is 100 W/mK. The insulation material is glass fiber and its outer surface is exposed to ambient air at 300 K. If the ambient air provides a convection coefficient of ho = 20 Internal flow Ambient air W/m?K, determine the followings: a. What are the thermal resistance coefficients for convections and conductions b. What is the heat transfer rate per unit length of the pipe c. If the pipe is 30 m long, what will be total heat transfer rate from the pipe. t00 noints)arrow_forwardHomework O H.W. 1: The walls of a refrigerator are typically constructed by sandwiching a layer of insulation between sheet metal panels. Consider a wall made from fiberglass insulation of thermal conductivity k; = 0.046 W/m.K and thickness L, = 50 mm and steel panels, each of thermal conductivity k, = 60 W/m.K and thickness L, = 3 mm. If the wall separates refrigerated air at T = 4 C from ambient air at T,. = 25 C, what is the heat gain per unit surface area? Coefficients associated with natural convection at the inner and outer surfaces may be approximated as h, = h, = 5 W/m?.K. %3D %3D L; = 0.050 m K K Lo = 0.003 m Refrigerated air Ambient air Too.i = 4°C hi = 5 W/m2-K To,o = 25°C ho = 5 W/m2-K %3D Panel (2) kp = 60 W/m-K Insulation k; = 0.046 W/m-K 22 Warith Alanbiyaa (Dr. ALI M) Heat Transfer Page 11 ofarrow_forward
- Q₁: Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k-2.3 W/m °C, and surface area A= 20 m². The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T-15 °C with a heat transfer coefficient of h=24 W/m² °C. Assuming constant thermal conductivity and no heat generation in the wall, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the wall, (b) obtain a relation for the variation of temperature in the wall by solving the differential equation, and (c) evaluate the rate of heat transfer through the wall Ans: (c) 6030 Warrow_forwardA long rod with a thermal conductivity of 1 W / m · K is subjected to the boundary conditions given in the figure. Find the temperature distribution in the steady state with the energy balance method for ∆x = ∆y = 0.2m. Also calculate the heat transfer between rod and fluid per unit length.arrow_forwardQ3: A steam pipe of outside temperature of (T = 500 °C) and outside radius of (R. 100 mm) is insulated with three layers of thermal insulation materials of equal thickness of (t 100 mm), as shown in Fig. Q.3. The thermal insulation is exposed to an ambient temperature of (T = 20 °C). If the thermal conductivity of the thermal insulation layers are (K₁ = 0.4 W/m. K), (K₂ = 0.25 W/m. K) and (K3 = 0.1 W/m. K) and the convection heat transfer coefficient is (h = 40 W/m2.K). Find the temperature distribution along the three layers of thermal insulation materials using the FVM with a uniform grid of (Ar = 50 mm). The one- dimensional steady state energy equation for this problem is given as follows: 1 d r dr (rk: dT = 0 h-40 W/m².K T-20°C 7,500 C Fig. Q.3 K₁ =0.4 W/m.K K₁ = 0.25 W/m.K K₁ 0.1 W/m.Karrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Ficks First and Second Law for diffusion (mass transport); Author: Taylor Sparks;https://www.youtube.com/watch?v=c3KMpkmZWyo;License: Standard Youtube License