Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 9, Problem 9.92P
(a)
To determine
The ratio of the convective heat rate for the horizontal section to that of the vertical section.
(b)
To determine
Theeffect of inserting a baffle at the mid-height of the vertical section.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Chips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosure
whose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity of
ε=0.60 and a maximum allowable temperature of Ts=85oC.
(a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operating
power of each chip? The convection coefficient may be approximated as h=11.7 W/m2K.
(b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forced
convection, with h=250 W/m2K, what is the maximum operating power?
A black thermocouple
measures the temperature in a
chamber with black walls. If the
air around the thermocouple is
at 20°C, the walls are at 100°C,
and the heat transfer
coefficient between the
thermocouple and the air is 15
W/m?K, what temperature will
the thermocoule read?
A house with a flat horizontal roof has a black tar waterproof finish. the underside of the roof is well insulated. The upper surface is exposed to ambient air at 298 K. The convection heat transfer coefficient is 11W/m2K. Calculate the average equilibrium temperature of the roof for the following conditions;
(i) Clear sunny day with incident solar radiation flux of 500W/m2
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- asaparrow_forwardThe production line of a special biscuit at 30 ̊C and 1 atm has a 0.8 X 0.8 (m) square plate. One side of the plate is maintained at a temperature of 100 ̊C, while the other side is insulated. Determine the rate of heat transfer from the plate by natural convection if the plate (i) Is horizontal with the hot surface facing down; (ii) Is horizontal with the hot surface facing up; Data: The properties of air at the film temperature are: thermal conductivity, k= 0.0279 W/m.k); kinematic viscosity= 1.815 x 10-5 m2/s; Pr = 0.709arrow_forwardA horizontal cylindrical rod with a length of 2 m and a diameter of 0.2 m is used for the top of a swing set. On a sunny summer day, the temperature of the rod is 40°C and the temperature of the quiescent air is 30°C. What is the convective heat transfer rate from the rod?| 41-6 warrow_forward
- Consider a horizontal 5-mm-thick, 80-mm-long straight fin fabricated from plain carbon steel (k = 57 W/m-K, = 0.5). The base of the fin is maintained at 100°C, while the quiescent ambient air and the surroundings are at 25°C. Assume the fin tip is adiabatic, and estimate the fin heat rate per unit width, a', in W/m. Use an average fin surface temperature of 80°C to estimate the free convection coefficient, and the linearized radiation coefficient,,, in W/m²K. a's = h= ܐ h₂ = i i W/m W/m².K W/m².Karrow_forward. Natural Convection Heat Loss in Double Window. A vertical double plate-glass window has an enclosed air-gap space of 10 mm. The window is 2.0 m high by 1.2 m wide. One window surface is at 25°C and the other at 10°C. Calculate the free con- vection heat-transfer rate through the air gap.arrow_forwardA vertical cylinder 1.5m high and 180 mm in diameter is maintained at 100C in an atmosphere environment of 20C.calculate heat loss by free convection from the surface of the cylinder for air take p=1.06 kg/ m2.v=18.97*10 -6 m2/s.Cp=1.004kJ/kg2C and k=0.1042kJ/ mh2Carrow_forward
- Question 3: A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in the sketch. On a cold winter day the convection heat transfer coefficients are ho 60 W/m2 K and hi 30 W/m2 K. The total wall surface area is 350 m2. (a)Determine the total heat loss through the wall. (b) If the wind were blowing violently, raising ho to 300 W/m2 K, determine the percentage increase in the heat loss.arrow_forwardThe wall of a box furnace is made of a composite material. Layer A is directly in contact with the combustion gases inside the furnace and it has a thickness of 0.023 m, a thermal conductivity of 132 W/m-K, and a cross-sectional area of 0.42 m2. On the other hand, Layer C corresponds to the outermost layer that is in direct contact with the ambient air. It has a thickness of 0.036 m, a thermal conductivity of 2 W/m-K, and has the same cross-sectional area as Layer A. In between Layer A and Layer C are two parallel layers: LayerB and Layer D. Layer B has the same cross-sectional area as Layer D. The thickness of Layer B and Layer D is 0.066 m. Layer B has a thermal conductivity of 13 W/m-K; while, Layer D has a thermal conductivity of 23 W/m-K. The combustion gases inside the furnace has a temperature of 373 ; while, the ambient air has a temperature of 30 . Finally, the convection heat transfer coefficients at the inside and outside of the wall are 111 W/m2-K and 22 W/m2-K…arrow_forwardChips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosurewhose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity ofε=0.60 and a maximum allowable temperature of Ts=85oC.(a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operatingpower of each chip? The convection coefficient may be approximated as h=11.7 W/m2K.(b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forcedconvection, with h=250 W/m2K, what is the maximum operating power?arrow_forward
- Question A5 To improve indoor air quality, an Edinburgh pub has installed a vertical glass screen to cover the opening of its fireplace. The square-shaped screen has a side of length 1.5 m and a surface temperature of 232°C. Determine the heat transfer from the fireplace to the room if the ambient and wall temperatures are both 22°C and the emissivity of the glass surface is 0.9. (Use the following for air: k = 3.38 x 10-2 W/mK, v = 2.641 x 105 m²/s, Pr = 0.690.) %3Darrow_forwardquestion in image need help with part c onlyarrow_forwardA circular grill of diameter 0.15 mand emissivity 0.7 is maintained at a constant surface temperature of 137°C in a horizontal position. What electrical power is required when the room air and surroundings are at 27 °C?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license