Consider laminar flow about a vertical isothermal plate of length L, providing an average heat transfer coefficient of
Want to see the full answer?
Check out a sample textbook solutionChapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
Introduction to Heat Transfer
Statics and Mechanics of Materials
Engineering Mechanics: Statics
Heating Ventilating and Air Conditioning: Analysis and Design
Thermodynamics: An Engineering Approach
- Water enters a tube at 29°C with a flow rate of 460 kg/h. The rate of heat transfer from the tube wall to the fluid is given as qs′(W/m)=ax, where the coefficient a is 25 W/m2 and x(m) is the axial distance from the tube entrance. (a) Beginning with a properly defined differential control volume in the tube, derive an expression for the temperature distribution Tm(x) of the water. (b) What is the outlet temperature of the water for a heated section 31 m long? (c) Sketch the mean fluid temperature, Tm(x), and the tube wall temperature, Ts(x), as a function of distance along the tube for fully developed and developing flow conditions. (d) What value of a uniform wall heat flux, qs″ (instead of qs′=ax), would provide the same fluid outlet temperature as that determined in part 8.13b? For this type of heating, sketch the temperature distributions requested in part 8.13c.arrow_forwardHeat Transferarrow_forwardin convection heat transfer, what happen to the heat transfer coefficient if the viscosity of the fluid decrease?arrow_forward
- For fluids with small Prandt number the thermal boundary layer development is much ....................than that of the velocity boundary layer (δt ≫ δ), and it is reasonable to assume ....................... velocity (u = u∞) throughout the thermal boundary layer. Please fill the blankarrow_forward350 pipes are fixed as square in a pipe bundle used for condenser. PipeThe outer diameters are 8 mm and the steam at 0.2 bar is desired to be condensed on the pipes. pipe outer The surface temperature is kept constant at 30 °C. If the length of the pipes is 1.5 m, the heat transferred in the systemCalculate the amount of energy and the amount of condensed steamarrow_forwardQ1: Consider a wall heated by convection on one side and cooled by convection on the other side. Show that the heat-transfer rate through the wall is T1-T2 1/h A+A/kA+ 1/h2A Where T; and T; are the fluid temperatures on each side of the wall and h, and h; are the corresponding heat-transfer coefficients.arrow_forward
- Q1: (5pt) In a cylindrical fuel element for a gas-cooled nuclear reactor, the generation rate of thermal energy within the fuel element due to fission can be approximated by the relation q(1) W/m³ %3D where a is the radius of the fuel element and is constant.The boundary surface at r = a is maintained at a uniform temperature Tɔ. (a) Assuming one-dimensional, steady-state heat flow, develop a relation for the temperature drop from the centreline to the surface of the fuel element. (b) For a radius of a = 30 mm, the thermal conductivity k = 10 W/(m °C) and qo = 2 x 107 W/m³, calculate the temperature drop from the centreline to the surface. 02: (5pt)arrow_forwardThe ascending order of below given gasses in view of the thermal conductivity with molar mass is 1. Air 2. Argon 3. Helium (A) 2, 3, 1 (В) 3, 2, 1 (C) 2, 1, 3 (D) 1, 3, 2arrow_forwardIn thermally fully developed flow of a fluid with constant properties, the local convection coefficient is .......................... , ........................ please fill the blank Blank 1( a constant or not a constant) Blank 2 ( dependent on or independent of)arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning