Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 9, Problem 9.85P
To determine
The rate of heat transfer per unit width normal to flow direction.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A cylindrical tube has an inner diameter of 2 cm and a wall thickness of 1 cm. The tube is evacuated. In the center, there is a radiation source along its axis that sends 1e^5 W/m^2 to the inner surface of the tube. K for the tube wall is 2 W/m K. If the outer surface of the tube is cooled with water at 298 K with a convective heat transfer coefficient of 100 W/m^2 K, determine the minimum temperature rating for the tube material for safe operation.
A radiant heating lamp has a surface temperature of 800 K with ε = 0.6 How large a surface area is needed to provide 350 W of radiation heat transfer?
You have 1.4 Langley's available in your area. Assuming about 11 hours of sunlight
per day and a south facing solar collector angled to equal your latitude. How much
energy (Btu's) can you expect to collect with a 90 ft2 collector and 62% efficiency in
364 days?
Your Answer:
Answer
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Correct answer onlyarrow_forwardConsider a large plane wall of thickness L = 0.8 ft and thermal conductivity k = 1.2 Btu/h-ft-°F. The wall is covered with a material that has an emissivity of ε = 0.80 and a solar absorptivity of a = 0.60. The Inner surface of the wall is maintained at T₁ = 524 R at all times, while the outer surface is exposed to solar radiation that is incident at a rate of q solar = 300 Btu/h-ft2. The outer surface is also losing heat by radiation to deep space at O K. 0 Plate a solar o = 0.1714 x 10-8 Btu/h ft2 R4 Sun If the temperature of the outer surface of the wall is 556.39 R, determine the rate of heat transfer through the wall when steady operating conditions are reached. (Round your answer up to 2 decimal places.) 51 Btu/h-ft2 (per The rate of heat transfer through the wall when steady operating conditions are reached unit area)arrow_forwardFind the total heat flux of the composite wall when: B F KA = KC = KF = 15 т. К A E KB = KD = 10 т. К KE = KG = 20 т. К D. Height of B = C = D 4 cm 3 cm 4 cm 6 cm Height of F = G AT = 30 K て)arrow_forward
- Consider an alumınum pan used to cook food on top of an electric range. The bottom section of the pan has thickness of L = 0.3 cm and diameter of D = 20 cm. The electric heating unit transfers 800 W of power to the pan. During steady operation. the temperature of the inner surface of the pan is measured to be 110 C. Which of the following boundary conditions is correct during this cooking process; Waler 4. a. Nore of the options D. 25.46 KW/m- T-1)= 110 C %3D Oc T,-o 110 °C & 4x=L 800 W m- %3D d. 9=0 = 800 Wm? To-03m)= 110°Carrow_forwardThe inner wall of thermos bottle is at 0°C while the outer at 37°C. The space between the walls is evacuated and the walls are silvered so the emissivity is reduced to 0.10. If each wall has an area of 700 cm2, how much energy is transformed by radiation between the walls each second?arrow_forwardOne side of a copper block 5 cm thick is maintained at 250 C. The other side is covered with a layer of fiberglass 2.5 em thick. The outside of the fiberglass is maintained at 35-C, and the total heat flow through the copper- fiberglass combination is 52 kW. What is the area of the slab?arrow_forward
- The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Illustrate the order of arrangement of bricks A and B in the furnace wall (with thickness, estimated temperatures at the interface between walls A and B and at the interior and exterior surface, the transport area and direction of transfer included)arrow_forwardThe inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. If a 15 ft2 wall is to be constructed, how many bricks will be used? how many brick A and how many brick B?arrow_forwardThe inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. Model the wall as one-dimensional and determine the most economical arrangement of the bricks. Include:a drawing labeled with all given informationthe variables used in the appropriate places on the drawing (along with values and units, if provided)a thermal circuit showing the paths for heat transmissionequations and calculationsCalculations that show that the maximum temperature for Type A brick does not exceed 1400oFA recommendation for the number and orientation of the bricks. The inside temp is 2100f…arrow_forward
- The inside wall of a furnace is at 2100oF and the outside wall is at 300oF. The wall of a furnace must be designed to transmit no more than 220 Btu/hr-ft2. Two types of bricks are available for construction:TYPE A: k = 0.38 Btu/ hr-ft-R with an allowable maximum temperature of 1400oFTYPE B: k = 0.98 Btu/ hr-ft-R with an allowable maximum temperature of 2300oF Both types of bricks have the same dimensions (9” x 4.5” x 3”) but the cost for Type B brick is twice the cost of Type A brick. What is the rate of heat conduction through wall A? If a 15 ft2 wall is to be constructed, how many bricks will be used? how many brick A and how many brick B?arrow_forwardYou want to heat a house on a very cold day as shown in the figure. To do this, you want to use photovoltaic panels as an energy source. It would be about using 15 panels each with an area of 1.5 m2. These panels would be connected to an electrical resistance that would heat the house as shown in the figure. The house is losing heat through the walls and ceiling as shown in the figure. The panels are receiving solar radiation at a rate of 800 W / m2 and if their efficiency is 15%. How much will the temperature of the house rise after an hour? The house is hermetically sealed. Assume that the specific heats of air, cv and cp, are constant as shown in the figure. sol = sun fuga = leakage aire = airarrow_forwardA wood stove is used to heat a single room. The stove is cylindrical in shape, with a diameter of D = 0.400 m and a length of L = 0.500 m, and operates at a temperature of T, = 200 °C. (a) If the temperature of the room is T, = 20°C, determine the amount of radiant energy delivered to the room by the stove each second if the emissivity of the stove is e = 0.920. (b) By definition, the R-value of a conducting slab is given by Atot(Th – To) Poond R = where Atot is the total surface area, Pcond is the power loss by conduction through the slab, Th and Te are the temperatures on the hotter and cooler sides of the slab. If the room has a square shape with walls of height H = 2.40 m and width W = 7.60 m, determine the R-value of the walls and ceiling required to maintain the room temperature at T = 20°C if the outside temperature is T, = 0°C. Note that we are ignoring any heat conveyed by the stove via convection and any energy lost through the walls and windows via convection or radiation.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license