Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 9, Problem 9.117P
To determine
The drying rate per unit width of the garment.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Estimate the interfacial heat transfer coefficient for evaporation of a thin film of
saturated liquid water at atmospheric pressure. The liquid film rests on a flat, solid
surface to which a constant and uniform heat flux of 150 kW/m? is applied. The
accommodation coefficient may be taken to be 0.05. If the liquid film thickness is 0.2
mm, compare the interfacial vaporization resistance with the conduction resistance
through the liquid film.
Please solve ASAP
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge?
I need the solution from fundamental concepts of how the heat flow behaves in the system
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Include drawingarrow_forwardYou have a 2 mm thick layer of water on the floor of a room. The water vaporizes and diffuses through a stagnant film of air, estimated to be 2.5 mm thick, on the surface of the water. Under the evaporation condition, consider as an approximation that the temperature of the water is essentially equal to its dry bulb temperature, 28 ° C. Calculate the time required for the water layer to completely disappear, for thecase the floor is porous and the water also penetrates the floor at a constant rate of 0.1kg / (m2.h).Calculate the vapor pressure of water using the Antoine equation below. The diffusivity of water vapor in air is 0.2201 cm2 / s at 1 atm and 0 ° C. The vapor pressure, P ° (in bar), of the water is given by: ln (P °) = 13.8573 - 5160.2 / T, where T is the temperature in K.arrow_forwardWater at 25°C flows over a 30mm diameter cylinder with an embedded electrical heater. The cylinder is 1m in length with a surface temperature of 90°C. If the supplied power is 28 kW/m, what is the convection coefficient?arrow_forward
- 3. Consider a hot automotive engine, which can be approximated as a 0.6 m high, 0.3 m wide, and 0.9 m long rectangular block. The bottom surface of the block is at a temperature of 90°C and has an emissivity of 0.9. The ambient air is at 23°C, and the road surface is at 28°C. The fluid properties of air are determined at the film temperature and can be found in the tables at the end of the tutorial. a. Determine the rate of heat transfer from the bottom surface of the engine block by convection and radiation as the car travels at a velocity of 60 km/h. b. If the temperatures were measured with a thermometer accurate to the nearest 1°C, what in the resultant heat is the uncertainty transfer rate? (You may ignore the uncertainties when calculating your fluid properties). c. If the speedometer in the car is accurate to the nearest 2km/h, what is the uncertainty in the result?arrow_forwardFUNDAMENTALS OF CONVECTION Consider a flat plate positioned inside a wind tunnel, and air at 1 atm and 20°C is flowing with a free stream velocity of 60 m/s. What is the minimum length of the plate necessary for the Reynolds number to reach 2x107? If the critical Reynolds number is 5x105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subjectarrow_forwardThermal energy generated by the electrical resistance of a 5-mm-diameter and 4-m- long bare cable is dissipated to the surrounding air at 80°C. The voltage drop and the electric current across the cable in steady operation are measured to be 18 V and 5 A, respectively. Disregarding radiation, estimate the surface temperature of the cable. Evaluate air properties at a film temperature of 100°C and 1 atm pressure.arrow_forward
- The pressure is 101.32 kPa and the air velocity at 316.5 k is 0.61m / s. The surface of the sphere is 277.76 k and its average diameter is 114 mm. Calculate the heat transfer coefficient for the air blown aroundarrow_forwardAn open tank, 6 mm in diameter, contains 1 mm deep layer of benzene (Mol wt = 78) at its bottom. The vapour pressure of benzene in the tank is 13.15 kN/m2 and its diffusion takes place through a stagnant air film 2.5 mm thick, At the operating temperature of 20°C, the diffusivity of benzene in the tank is 8.0 x 10-6 m2/s. If the benzene has a density of 880 kg/m³, calculate the time taken for the entire benzene to evaporate. Take atmospheric pressure as 101.3 kN/m² and neglect any resistance to diffusion of benzene beyond the air film. %3Darrow_forwardQuestion 4: Consider a sphere with a diameter of 25 mm and a surface temperature of 60°C that is immersed in a fluid at a temperature of 30°C and a velocity of 2 m/s. Calculate the drag force and the heat rate when the fluid is (a) water and (b) air at atmospheric pressure. Explain why the results for the two fluids are so different.arrow_forward
- How does an increase in gas temperature affect pressure drop in a haghouse, assuming the mass flow rate of particles and the molar flow rate of gas are constant?arrow_forwardHow is storage modulus and loss modulus relate with diffussivity of a drug molecule pass through a gel? Does higher storage modulus means lower difussivity?arrow_forwardA manufacturing plant produces an efluent as a waste product. As part of a waste heat recovery system, they want to use this for internal heating and cooling. The effluent is flown through a system where its temperature remains at 303.15 K. A 0.06-m diameter pipe carrying hot water and 0.04-m diameter pipe carrying cold air is passed through this effluent chamber. It can be assumed that the surface temperature of these air and water pipes are same as the effluent temperature. Water comes in at 328.15 K and exits at 308.15 K. The air comes in at 268.15 K and exits at 298.15 K. The mass flow rate of water and air is respectively, 1 kg/s and 0.01 kg/s. Determine the length of the water and air pipes in the system. Convert all calculations to C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license