Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.77P
A sphere of 25-mm diameter contains an embedded electrical healer. Calculate the power required to maintain the surface temperature at 94°C when the sphere is exposed to a quiescent medium at 20°C for (a) air at atmospheric pressure, (b) water, and (e) ethylene glycol.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
7. A 1.5-cm diameter, electrically heated sphere is placed in a quiescent air at 20°C. Calculate the
amount of heat to be supplied by the electric heater in order to keep the surface temperature
of the sphere at 100°C.
Consider two solid copper spheres, 1 and 2. Sphere 1 has twice the diameter of sphere 2. If both
spheres are initially at 0 °C and placed in quiescent air at 25 °C, which sphere will reach air
temnerature first?.
sphere 1
sphere 2
both spheres will reach temperature at the same time
I need the solution in hand writing ..
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The surface temperature of the hot side of the furnace wall is 1200 degrees C. It is desired to maintain the outside of the wall at 38 degrees C. A 152 mm of refractory silica is used adjacent to the combustion chamber and 10 mm of steel covers the outside. What thickness of insulating bricks is necessary between refractory and steel, if the heat loss should be kept at 788 W/m2? Use k=13.84 W/m-K for refractory silica; 0.15 for insulating brick, and 45 for steel.arrow_forwardYou went to Target to buy some masks. As you walk up to the store, you notice the huge red balls in front of the store. Air outside is quiescent. If the sphere surface has a temperature of 17°C and the quiescent air has a temperature of 22.5°C, find the convective heat transfer rate from the sphere. The diameter of sphere is 1 m. -66warrow_forwardThe surface temperature of the hot side of the furnace wall is 1200°C. It is desired to maintain the outside of the wall at 38°C. A 152 mm refractory silica is used adjacent to the combustion chamber and 10 mm of steel covers the outside. What thickness of insulating bricks is necessary between refractory and steel, If the heat loss should be kept at 788 W/m2? use k = 13.84 W/m-K fro refractory silica; 0.15 for insulating brick, and 45 for steel. O 260 mm 280 mm O 240 mm 220 mmarrow_forward
- Water at 25°C flows over a 30mm diameter cylinder with an embedded electrical heater. The cylinder is 1m in length with a surface temperature of 90°C. If the supplied power is 28 kW/m, what is the convection coefficient?arrow_forwardThe surface temperature of the hot side of the furnace wall is 1200°C. It is desired to maintain the outside of the wall at 38°C. A 152 mm of refractory silica is used adjacent to the combustion chamber and 10 mm of steel covers the outside. What thickness of insulating bricks is necessary between refractory and steel, if the heat loss should be kept at 788 W/m²? Use k = 13.84 W/m-K for refractory silica; 0.15 for insulating brick, and 45 for steel. Badly needed asap. I will rate helpful. Thank you in advance.arrow_forwardA 212-mm-square, 15-mm-thick tile has the thermo-physical properties of Pyrex (ϵ = 0.83) and emerges from a curing process at an initial temperature of Ti = 145°C. The backside of the tile is insulated while the upper surface is exposed to ambient air and surroundings at 25°C. (a) Estimate the time required for the tile to cool to a final, safe-to-touch temperature of Tf = 42°C. Use an average tile surface temperature of T¯=(Ti+Tf)/2 to estimate the average free convection coefficient and the linearized radiation coefficient. How sensitive is your estimate to the assumed value for T¯? (b) Estimate the required cooling time if ambient air is blown in parallel flow over the tile with a velocity of 10 m/sarrow_forward
- After going through the production process, thin plates with a length of 0.9m are cooled by suspending them vertically in an atmosphere of quiescent hydrogen at 80°C. To maximize production throughput, the plates are hung as close together as possible. There is a concern however, that if the plates are too close together, the cooling will take longer, costing the company additional money. If the plates are initially at a temperature of 110°C, what is the minimum plate spacing that would avoid interference between their free convection boundary layers? Thermos-physical properties are shown in the table below. Thermal Diffusivity [m2/s] 2.446*10-4 Kinematic Viscosity [m2/s] 1.573*104 Prandtl Number [-] 0.6969arrow_forward7. Consider a plate and a cylindrical fuel element made of uranium metal. The thickness of the plate fuel element is equal to the radius of the cylindrical fuel element. Show that the maximum to surface temperature difference of the plate fuel element is twice that of the cylindrical fuel element. State your assumptions.arrow_forward3. An electric immersion heater, 10 mm in diameter and 300 mm long, is rated at 550 W. The emissivity of the heater is ε = 0.85. a) If the heater is horizontally positioned in a large tank of water at 20°C, estimate its surface temperature. b) If the heater is accidentally operated in air at 20°C, estimate the surface temperature. Hint: Radiation heat transfer can be neglected in liquids, but not in gases like air.arrow_forward
- A school classroom is 6 m long, 6 m wide and 3 m high. There is a 2.5 m x 4 m window in the east wall. Only the east wall/window is exterior. Assume the thermal conditions in adjacent spaces (west, south, north, above and below) are the same as those of the classroom. Determine the cooling load at 9:00 am, 12:00 noon on July 21. Other known conditions include: Latitude = 40o N Ground reflectance = 0.2 Clear sky with a clearness number = 1.0 Overall window heat transmission coefficient = 7.0 W/m2.K Room dry-bulb temperature = 25.5°C Permissible temperature exceeded = 2.5% Schedule of occupancy: 20 people enter at 8:00 am and stay for 8 hours Lighting schedule: 300 W on at 8:00 AM for 8 hours Exterior wall structure: • Outside surface, A0 • Face brick (100 mm), A2 • Insulation (50 mm), B3 • Concrete block (100 mm), C3 • Inside surface, E0 Exterior window: • Single glazing, 3 mm • No exterior shading, SC = 1.0arrow_forwardA plate is maintained at 74°C and this surface is facin an air having temperature of 30°C, then what will be th value of coefficient of volumetric expansion ß?arrow_forwardPROBLEM 4: A black thermocouple is inside a chamber with black walls. If the air around the thermocouple is at 20°C, the walls are at 100-C, and the heat transfer coefficient between the thermocouple and the air is 75 W/m²K, what temperature will the thermocouple read?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license