Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.5P
In many cases, we are concerned with free convection involving gases that are contained within sealed enclosures. Consider air at 27°C and pressures of 1, 10, and 100 bars. Determine the figure of merit described in Problem 9.4 for each of these three pressures. Which air pressure will provide the most effective cooling? Hint: See Problem 6.22.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The onset of free convection. Plastic shrink wrap can be used to insulate windows by trapping air between your window and the wrapping. Calculate the critical gap width between the plastic and the window at which free convection will occur on an average winter’s day, when the outside temperature is 41°F and the inside temperature is 68°F. Would you expect there to be more or less heat transfer when the spacing is above this gap? Explain.
There are 2 options to be considered to form the insulation layer between the refractory
brick and air space, which are fiberglass and firebrick. Calculate the minimum thickness
required for the both fiberglass and firebrick. Which option do you recommend?
Comment. State the assumption in your calculation.
Based on your recommendation, calculate the temperature at each interface throughout the
wall and draw a temperature variation diagram from inside wall surface to outside wall
surface.
* Refractory
brick
Fiberglass or
firebrick?
0.5" Plaster
Heat
Ambient
source
Air spáce
4 Concrete block
Figure 2
Question One
Explain how heat is transferred from one point to another illustrating with appropriate diagram.
Calculate the heat flow per square meter (heat flux) through water medium with thermal conductivity of 0.6, flowing in a 5 cm thickness space, if the temperatures on the two surfaces are 50 and 210°C, respectively.
Question 2
Distinguish between force and free convection with the aid of appropriate illustrations.
What is the approximate temperature difference between a hot plate and the surrounding air if the heat flux from the plate is 800 W/m2? Assume that the air is flowing past the surface with a velocity of 5 m/s giving a heat transfer coefficient of 20 W/(m2K).
Question 3
Explain the differences between laminar and turbulent flow
Water (ν = 0.86x10-6m2/s) flows through a tube with the diameter 12 mm at a velocity of 2 m/s. Determine if the flow is laminar or turbulent!
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Question No. 1 Gaseous carbon dioxide at 1 atm and 300°C is flowing inside a horizontal pipe that has 5.3 cm ID and 6.0 cm OD. The flow velocity of carbon dioxide is 15 m/s. The outside surface of the pipe is exposed to the atmospheric air that has temperature of 40°C. Considering free convection conditions at the outer pipe surface and assuming pipe wall temperature as 200°C, calculate the inside overall heat transfer coefficient, outside heat transfer coefficient, and overall heat transfer coefficient based on the inside surface of the pipe. Warning: Calculate both the inside and the outside heat transfer coefficients only using the respective correlations and ignore radiation effects.arrow_forwardDon’t use Heissler charts to answer this question Heat sterilization of lumber, timbers, and pallets is used to kill insects to prevent their transfer between countries in international trade. This is analogous to food sterilization by heat. A typical requirement here is that the slowest heating point of any woodconfiguration be held at 56 °C for 30 minutes. Consider hot air heating of wooden boards that maintains their surface temperature at 70 °C. The boards are stacked outside and in the winter time they can be considered to be at 0 °Cwhen theyare brought in for heating. The thermal diffusivity of the wood is 9*10-8m2/s. a.Calculate the time from the start of heating for a 2.5 cm thick board to reach a sterilization temperature of 56 °C at its slowest heating point .b.Calculate the heating time when four such boards are stacked together. c.Calculate the ratio of the two heating times (for a single board versus when they are stacked), and explain the ratio. Note: You’re free to…arrow_forward2. Consider a vertical, single-pane window of width = height = 1 m. The interior surface is exposed to the air and walls of a room, which are each at 18°C. Under cold ambient conditions for which a thin layer of frost has formed on the inner surface, what is the heat loss through the window? As with most natural convection problems, radiation heat transfer may NOT be neglected. Use Trad =EσA (T-T4) with & = 0.90.arrow_forward
- An underwater sonar that maps the ocean bathymetry is encapsulated in a sphere with a diameter of 85 mm. During operation, the sonar generates heat at a rate of 300W. What is the sonar surface temperature when it’s located in a water column where the temperature is 15o C and the water current is 1 m/sec? The sonar was pulled out of the water without turning it off, thus, it was still working. The air temperature was 15o C and the air speed was 3 m/sec. What was the sonar surface temperature? Was there any reason for concern?arrow_forward(a) In thermal systems design projects various cost estimation methods can be followed depending on the nature of the project. Discuss at least four costing methods that can be applied in the thermal systems design and compare the strength and weakness of each method. (minimum 250 words). (b) Which method of costing do you think is appropriate for your thermal system design project? Discuss your justifications why you prefer the particular cost estimation method. (c) In the design process of air conditioning systems discuss the key steps you should carry out before production and installation of the system.arrow_forwardA school classroom is 6 m long, 6 m wide and 3 m high. There is a 2.5 m x 4 m window in the east wall. Only the east wall/window is exterior. Assume the thermal conditions in adjacent spaces (west, south, north, above and below) are the same as those of the classroom. Determine the cooling load at 9:00 am, 12:00 noon on July 21. Other known conditions include: Latitude = 40o N Ground reflectance = 0.2 Clear sky with a clearness number = 1.0 Overall window heat transmission coefficient = 7.0 W/m2.K Room dry-bulb temperature = 25.5°C Permissible temperature exceeded = 2.5% Schedule of occupancy: 20 people enter at 8:00 am and stay for 8 hours Lighting schedule: 300 W on at 8:00 AM for 8 hours Exterior wall structure: • Outside surface, A0 • Face brick (100 mm), A2 • Insulation (50 mm), B3 • Concrete block (100 mm), C3 • Inside surface, E0 Exterior window: • Single glazing, 3 mm • No exterior shading, SC = 1.0arrow_forward
- Question: a) We want to increase heat transfer by placing fans to provide forced convection to reduce the length of the pipe necessary (Note that the outside surface temperature of the pipe remains the same at 100oC). What is the rate of heat transfer from pipe to the air per meter length if the air speed over the pipe surface is 5m/s? What is the total length of the pipe necessary? Problem: Consider a rectangular warehouse with the dimensions of 40m long x 20m widex10m height. The overall heat transfer coefficient for all sidewalls is Uwall=0.3 W/m2K (Approx. R=20 hr.ft2.oF/Btu) and for the flat roof, it is Uroof= 0.20W/m2K. The floor can be assumed to be insulated and we can ignore the heat transfer through the doors, etc. We want to maintain the inside air temperature at 15oC while the outside temperature is 0oC by using a thin-walled, 5.0cm diameter copper pipe that carries steam. Steam enters the pipe as saturated vapor at 100oC. So, as it starts losing heat to the inside air, it…arrow_forward2. Clothing made of several thin layers of fabric with trapped air in between, often called ski clothing, is commonly used in cold climates because it is light, fashionable, and a very effective thermal insulator. So it is no surprise that such clothing has largely replaced thick and heavy old- fashioned coats. Multilayered ski jacket REBUTarrow_forwardTransport Phenomena Questionarrow_forward
- Please fats. The answer in the box is incorrectarrow_forwardPlease provide the answer with appropriate inages and stepsarrow_forward(a) Calculate the R-value of a thermal window made of two single panes of glass each 0.125 in. thick and separated by a 0.230-in. air space. (b) By what factor is the transfer of energy by heat through the window reduced by using the thermal window instead of the singlepane window? Include the contributions of inside and outside stagnant air layers.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license