Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470917855
Author: Bergman, Theodore L./
Publisher: John Wiley & Sons Inc
expand_more
expand_more
format_list_bulleted
Videos
Question
Chapter 9, Problem 9.54P
To determine
The temperature of rod for which the lumped capacitance approximation is applied.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
8. Consider an iron bar, of diameter 4cm and length 1m, with specific heat c =
0.437J/(g K), density p= 7.88 g/cm³, and thermal conductivity K = 0.836 W/(cm K).
Suppose that the bar is insulated except at the ends, it is heated to a constant tem-
perature of 5 degrees Celsius, and the ends are placed in an ice bath (0 degrees
Celsius). Compute the temperature (accurate to 3 digits) at the midpoint of the bar
after 20 minutes. (Warning: Be sure to use consistent units.)
Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential energy lost in the drop could be converted to thermal energy used to heat the copper from an initial temperature
of 25 degrees celsius, what would the final temperature of the copper wafer?
Would the answer be different if the wafer has a mass greater than 3 grams?
Note: the specific heat of copper is 387 J/(kg*K).
The temperature is between 25.8 and 26.0 degrees celsius, yes the bigger the mass the greater the energy.
O The temperature is between 25.6 and 25.8 celsius, answer does not depend on mass.
O The temperature is between 25.0 and 25.2 celsius, answer does not depend on mass.
O The temperature is 25.5 and of course the more mass something has the greater energy will be needed to raise the temperature.
The temperature is 26.2 and if the mass is doubled so will be the change in temperature.
O The temperature is 25.9 degrees celsius and the answer does not depend on mass.
O The…
A body having a cylindrical shape of length equals
temperature is equal to 300 K. The initial temperature of the body is equal to 350 K. If the heat convective coefficient is equal to 4.2
W/m^2.K. What condition should the thermal conductivity k verify in order to apply the lumped capacitance method.
1.9 m and diameter equals to 400 mm is inside a room where the ambient
Select one:
a. k is less than 4.2 W/m.K
b. k is greater than 1.6 W/m.K
O c. k is greater than 3.8 W/m.K
O d. k is less than 2.1 W/m.K
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- For flow over a slightly curved isothermal surface, the temperature distribution inside the boundary layer t can be approximated by the polynomial T(y)=a+by+cy2+d3(yt), where y is the distance normal to the surface. (a) By applying appropriate boundary conditions, evaluate the constants a, b, c, and d. Fluid (b) Then obtain a dimensionless relation for the temperature distribution in the boundary layer.arrow_forward3.9 The heat transfer coefficients for the flow of 26.6°C air over a sphere of 1.25 cm in diameter are measured by observing the temperature-time history of a copper ball the same dimension. The temperature of the copper ball was measured by two thermocouples, one located in the center and the other near the surface. The two thermocouples registered, within the accuracy of the recording instruments, the same temperature at any given instant. In one test run, the initial temperature of the ball was 66°C, and the temperature decreased by 7°C in 1.15 min. Calculate the heat transfer coefficient for this case.arrow_forwardFor each of the following cases, determine an appropriate characteristic length Lc and the corresponding Biot Bi number that is associated with the transient thermal response of the solid object. Say if the global capacitance approximation is va lid. If temperature information is not provided, evaluate properties T = 300K a)oroidal shape with diameter D = 50mm and cross-sectional area AC = 5 mm², with thermal conductivity k = 2.3W / (mK) The surface of the toroid is exposed to a refrigerant corresponding to a convective coefficient eta = 50 W/( m2.k) b)A long stainless steel heated bar (AISI 304), with rectangular cross section, and dimensions w = 3mm , W = 5mm and L = 100mm . the bar issubjected to a refrigerant that provides a heat transfer coefficient of h =15 W/(m2 K) on all exposed surfaces. c)A long extruded aluminum tube (2024 Alloy) with internal dimensions and external w = 20 mm and W = 24 mm , respectively, suddenly submerged in water, with a convective coefficient of h =…arrow_forward
- Asap, in detail pleasearrow_forwardFor what situations will the lumped capacitance method be valid if a solid is in contact with a fluid? Circle all appropriate answers. (a) The resistance to conduction within the solid is small compared to the resistance to convection due to a fluid. (b) The temperature gradient within the solid is large. (c) The Biot number is small (less than 0.1). (d) All of the above. (e) None of the abovearrow_forwardNeed help on the Q.arrow_forward
- A large 100-mm thick steel plate is initially at uniform temperature T = 180°C at time t = 0. Both sides of the plate are exposed to 30°C oil with convection coefficient h = 1500 W/m².K. The thermal conductivity, heat capacity, and density of the steel are k = 38 W/m-K, cp = 485 J/kg-K, and p = 7800 kg/m³. a) Find the temperature at the center of the slab when t = 125 s. b) Find the temperature at the surface of the slab when t=125 s.arrow_forward(a) Consider nodal configuration shown below. (a) Derive the finite-difference equations under steady-state conditions if the boundary is insulated. (b) Find the value of Tm,n if you know that Tm, n+1= 12 °C, Tm, n-1 = 8 °C, Tm-1, n = 10 °C, Ax = Ay = 10 mm, and k = = W 3 m. k . Ay m-1, n m, n | Δx=" m, n+1 m, n-1 The side insulatedarrow_forwardQ2/ An aluminum sphere weighting 7kg and initially at a temperature of 533K is suddenly immersed in a fluid at 283K. if heat transfer coefficient between the sphere and fluid is 50W/m?.°C. Take density=2707kg/m3, specific heat=0.9KJ/kg.ºC and thermal conductivity= 204W/m°C. Determine th Bi number and And determine the time required to cool sphere to 263karrow_forward
- Hi, kindly solve this problem and show the solution. Thank youarrow_forwardThe principles of Newton’s Law of Cooling. You can imagine and create your own data. Discuss the nature and origin of the four (4) types of coffee where it originates. Various settings, formulations, containers, and the number of trials will be properly discussed in their methodology. Once the experimentation has been done, the thermal coefficient shall be computed and recorded. The temperature coefficient acquired at t=0 and t= 5 mins, will be tested at t = 6,7,8,9 and 10 minutes.arrow_forwardIn 2012, a new fiber-optic cable of handling 40,000 telephone calls simultaneously was laid under the Pacific Ocean from California to Japan, a distance of 13,300 km. The cable was unreeled from shipboard at a mean temperature of 22oC and dropped to the Ocean floor having a mean temperature of 5oC. The coefficient of linear expansion of the cable is 75×10-6 /degree celsius. Determine the length of cable that must be carried on the ship to span the 13,300 Km. Also, find the percent change in lengtharrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license