Water is condensing on a square plate (0.5 m x 0.5 m) placed verCcally. If the desired rate ofcondensaCon is 0.016 kJ/s, determine the necessary surface temperature of the plate at atmosphericpressure. Assume the film temperature of 90 o C for evaluaCon of fluid properCes of water and thesurface temperature of 80 o C for the evaluaCon of modified latent heat of vaporizaCon

Water is condensing on a square plate (0.5 m x 0.5 m) placed verCcally. If the desired rate ofcondensaCon is 0.016 kJ/s, determine the necessary surface temperature of the plate at atmosphericpressure. Assume the film temperature of 90 o C for evaluaCon of fluid properCes of water and thesurface temperature of 80 o C for the evaluaCon of modified latent heat of vaporizaCon

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.29P

See similar textbooks

Similar questions

Q3/Condensing steam at 1 atm is used to maintain a vertical plate 20 cm high and 3.0 m wide at a constant temperature of 100°C. The plate is exposed to room air at 20°C. What flow rate of air will result from this heating process? What is the total heating supplied to the room air? Ans. 0.0034 kg/s, 278W
What is boiling and when does occurs? Explain pool boiling. How does it differ from forced convection boiling?
The boiling temperature of nitrogen at atmosphericpressure at sea level (1 atm) is -196°C. Therefore, nitrogenis commonly used in low-temperature scientific studies sincethe temperature of liquid nitrogen in a tank open to the atmosphereremains constant at -196°C until the liquid nitrogen inthe tank is depleted. Any heat transfer to the tank results inthe evaporation of some liquid nitrogen, which has a heatof vaporization of 198 kJ/kg and a density of 810 kg/m3 at1 atm.Consider a 4-m-diameter spherical tank initially filledwith liquid nitrogen at 1 atm and -196°C. The tank isexposed to 20°C ambient air with a heat transfer coefficientof 25 W/m2·K. The temperature of the thin-shelled sphericaltank is observed to be almost the same as the temperatureof the nitrogen inside. Disregarding any radiation heatexchange, determine the rate of evaporation of the liquidnitrogen in the tank as a result of the heat transfer from theambient air.
Palm oil with a density of 1200 kg/m3 and the specific heat of 2 kJ/(kg.K) is to be heated from 20oC to 80oC before further processing. The oilplaced in a vessel (vessel) cylindrical upright with a diameter of 2 meters.The height of the oil vessel inside is 2 meters. For this purpose, an electric heating element with an electrical resistance type of heat is used.The electrical resistance used is a 2 mm diameter conductor wire wrappedwith magnesium oxide material with a thermal conductivity of 0.4 W/(m.K) thick 2.5 mm, then coated with the outermost metal 0.5 mm thick. Occurring power density on the outermost metal layer should not be more than 25 kW/m2. Warm-up time is expected to be only about 1.5 hours. Calculate: a) Required electrical power? (in kW) b) Rating of the heater by meter length? c) Maximum temperature of the heater element?
See image
Corsidera circular smoth pipeof inner diameter D;=0.015mwhose inner surface is covered with a layer of liquid as a result of condensation. In order to dry the inner surface of the pipe, air at 300K at 1 atmis forced to flow throughit with anaverage velocity of 1.2m/s. Using the analogy between heat and mass trarsfer, detemine the mass transfer coeffícient irside the pipe for fully developed flow. Note: Viscosity of the air for given conditions is given as 1.58 x 10°n?/s. Also, for a lamirar fully developed flow the N=Sh=3.66. Your solution must state governing equations and associated assumptions, illustration and step by step execution of the overall solution
answer given are correct
The defroster of an automobile functions by discharging warm air on the inner surface of the windshield. To prevent condensation of water vapor on the surface, the temperature of the air and the surface convection coefficient (T¡,¡ ) must be large enough to maintain a surface temperature T, that is at least as high as the dewpoint (Ts,i ≥ Tdp). Step 1 00,0¹ kg 8 - 0 Consider a windshield of length L = 800 mm and thickness t = 6 mm and driving conditions for which the vehicle moves at a velocity of V = 70 mph in ambient air at T%0,0 = 0°C. From laboratory experiments performed on a model of the vehicle, the average convection coefficient on the outer surface of the windshield is known to be correlated by an expression of the form 1/3 Nu₁ = 0.037 Re8 Pr¹/³, where Re₁ = VL/v. Air properties may be approximated as k = 0.023 W/m·K, v = 12.5 × 10-6 m²/s, and Pr = 0.71. If Tdp = = 10°C and Ti 50°C, what is the smallest value of the inside convection coefficient required to prevent…
The water main in the cities must be placed at sufficientdepth below the earth’s surface to avoid freezing duringextended periods of subfreezing temperatures. Determine theminimum depth at which the water main must be placed ata location where the soil is initially at 15°C and the earth’ssurface temperature under the worst conditions is expected toremain at -10°C for a period of 75 days. Take the propertiesof soil at that location to be k = 0.7 W/m·K and a = 1.4 *1025 m2/s.
A vertical .2m by .2m square plate is exposed to saturated water vapor at atmospheric pressure. If the surface temperature is 80 degrees C and the flow is laminar, estimate the loal heat transfer coefficents at the middles and at the bottom of the plate.
Estimate the interfacial heat transfer coefficient for evaporation of a thin film of saturated liquid water at atmospheric pressure. The liquid film rests on a flat, solid surface to which a constant and uniform heat flux of 150 kW/m? is applied. The accommodation coefficient may be taken to be 0.05. If the liquid film thickness is 0.2 mm, compare the interfacial vaporization resistance with the conduction resistance through the liquid film.
Faster please