fas The condenser of a steam power plant operates at a pressure of 7.38 kPa (Tsat = 40°C). Steam at this pressure condenses on the outer surfaces of horizontal pipes through which cooling water circulates. The outer diameter of the pipes is 3 cm, and the outer surfaces of the pipes are maintained at 30°C. Determine the rate of condensation of steam per unit length of a horizontal pipe. The properties of water at the saturation temperature of 40°c are: hfg 2407 x 10^3/kg and pv=0.05 kg/m3. The properties of liquid water at the film temperature: pl = 994 kg/m3. Cpl =4178 J/kg C, ul = 0.72 x 10^-3 kg/m.s, ki = 0.623 W/m°C Select one: O a. 0.0046 kg/s O b.0.0036 kg/s O c.0.0016 kg/s O d.0.0026 kg/s

fas The condenser of a steam power plant operates at a pressure of 7.38 kPa (Tsat = 40°C). Steam at this pressure condenses on the outer surfaces of horizontal pipes through which cooling water circulates. The outer diameter of the pipes is 3 cm, and the outer surfaces of the pipes are maintained at 30°C. Determine the rate of condensation of steam per unit length of a horizontal pipe. The properties of water at the saturation temperature of 40°c are: hfg 2407 x 10^3/kg and pv=0.05 kg/m3. The properties of liquid water at the film temperature: pl = 994 kg/m3. Cpl =4178 J/kg C, ul = 0.72 x 10^-3 kg/m.s, ki = 0.623 W/m°C Select one: O a. 0.0046 kg/s O b.0.0036 kg/s O c.0.0016 kg/s O d.0.0026 kg/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

11(a) The displacement of a particle is given by s = 2t3 - 43t2 + 118t - 64 where s is in feet and t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 19 seconds of motion. After you have made the plots, answer the questions.
Plz complete this question Will upvote
2- The swinging motion of the upper arm may be described as the follows; 0= 10 sin 0.06 t where 0 is the relative angle between the upper arm and the trunk in sagittal plane and the time t ranged from 0 to 60 sec .plot angular position,velocity and acceleration and find the maximum acceleration.
Member AB is rotating at wAn = 8.4 rad/s. 200 mm 200 mm 200 mm 250 mm A Part A Determine the angular velocity of the member BPD measured clockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. You did not open hints for this part. ANSWER: гad/s WBPD = Part B Determine the I and y components of the velocity of point D. Express your answers using three significant figures separated by a comma. You did not open hints for this part. ANSWER: (Up)z. (Up)y = m/s Part C Determine the angular velocity of the member CD measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. You did not open hints for this part ANSWER:
1. please provide a complete solution, thank you!
Pls explain in DETAIL how did you come up with the solution. I'm going to present it in class and idk how to explain the Equations
For items 4-5, consider the slider-crank mechanism shown. Crank AB is 0.500 m long. Rod BD is 1.500 m long. The velocity at point B is 0.500 m/s, ↖45.0°. Which of the following gives the closest value to the speed of the piston at D? Which of the following gives the closest values of the lengths of the sides of the triangle formed by points B and D and point C, the instantaneous center of rod BD?
5. If a particle is rotating with an angular speed of 3.5 rad/s, how long does the particle take to go through one revolution?
TOPIC: KINEMATICS Specific Instructions: Solve each problem NEATLY and SYSTEMATICALLY. Show your COMPLETE solutions and BOX your final answer. Express your answers in 2 decimal places. Please write clearly.
Complete all parts to the problem, thanks!! All different parts are for the one problem
Hi please help: Find the angular acceleration produced by the drill, assuming it to be constant