Question 5. The diagram below shows a mass suspended from a tie supported by two horizontal braces of equal length. The tie forms an angle "a" of 60° to the horizontal plane, the braces form an angle 0 of 50° to the vertical plane. If the mass suspended is 10 tonnes, and the braces are 10m long, find: a) the force in the tie; & b) the force in the braces Horizontal Braces, Tie Mass

Question 5. The diagram below shows a mass suspended from a tie supported by two horizontal braces of equal length. The tie forms an angle "a" of 60° to the horizontal plane, the braces form an angle 0 of 50° to the vertical plane. If the mass suspended is 10 tonnes, and the braces are 10m long, find: a) the force in the tie; & b) the force in the braces Horizontal Braces, Tie Mass

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
Q3: The diagram shows the open bonnet of a car. The bonnet is vertical force V held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The car bonnet bonnet is 0.90 m long, has a weight of 25 N and its center of gravity G is 0.35 m from the hinge at O. 0.90m 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 2) By taking moments about O, show that the vertical force V applied at the end of the bonnet is 9.7 N. 60 horizontal hinge O 3) Calculate the magnitude of the force acting at the hinge O.
Q4: The diagram shows the open bonnet of a car vortical force V ijlull. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The bonnet is 0.90 m long, has a weight of 25 N and its center of gravity G is car bonnet- 0.35 m from the hinge at O. 0.90m 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 635m 2) By taking moments about 0, Proof that the vertical force V applied at the end of the bonnet is 9.7 N. horizonlal - hinge O 3) Calculate the magnitude of the force acting at the hinge O.
A 50 kg pole extends up a wall, making a 60° angle with the wall. The pole is supported by acable attached 3/4 of the way along the pole. This support cable is perpendicular to the wall.A 10 kg sign hangs from the end of the pole. The pole’s center of mass is 1/3 of the way fromthe wall to the end of the pole. (a) What is the tension in the cable?(b) What are the x and y components of the force the wall exerts on the pole?You must include an extended free body diagram showing all forces acting on the pole. Labelthe location on the pole you will use a reference for measuring distances (the “axis of rotation”) at the point where the pole touches the wall. Thank you!
:)A 1200 N uniform boom at o = 65.0 degrees to the horizontal is supported by a cable at an angle 0 = 25.0 degrees to the horizontal. The boom is pivoted at the bottom, and an object of weight m = 2.00E3 N hangs from its top. Find (a) the tension in the support cable and (b) the components of the force exerted by the floor on the boom (through the hinge).
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
Question 2) The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal. Response
clockwise. (Info missing from Question 3.PNG) Please look at the images for details about the question.
4. A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping. Draw the FBD
The uniform plate has a weight of W = 450 lb. Suppose that F= 250 lb. The plate is supported by cables A, B, and C as shown below. Determine: A) The tension in the supporting cable A. B) The tension in the supporting cable B. C) The tension in the supporting cable C.
Q3: The diagram shows the open bonnet of a car. The bonnet is yarie tore V held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The is 0.90 m long, has a weight of 25 N and its center of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. 2) By taking moments about 0, show that the vertical force V applied at the end of the bonnet is 9.7 N. Neg 0 3) Caleulate the magnitude of the force acting at the hinge O.
clockwise. (Rest of info for question 2 info.PNG)