Water at 20 o C enters the 4 cm-diameter, 14 m-long tube at a rate of 0.8 kg/s. The surfacetemperature of the pipe is maintained at 165 o Cby condensing geothermal stream at the shellside of the heat exchanger. Use water properCesat 85 o C for all calculaCons.(a) Show that the water flow is turbulent and thermally fully developed. (b) EsCmate the heat transfer coefficient for convecCve heat transfer from the pipe to the water. For a fully developed turbulent flow within the smooth pipe, the Nu number can becalculated from the following equaCon:(c) Calculate the exit temperature of the water. (d) Share your opinion on whether the use of water properties at 85°C is appropriate. Yes or No because:

Water at 20 o C enters the 4 cm-diameter, 14 m-long tube at a rate of 0.8 kg/s. The surfacetemperature of the pipe is maintained at 165 o Cby condensing geothermal stream at the shellside of the heat exchanger. Use water properCesat 85 o C for all calculaCons.(a) Show that the water flow is turbulent and thermally fully developed. (b) EsCmate the heat transfer coefficient for convecCve heat transfer from the pipe to the water. For a fully developed turbulent flow within the smooth pipe, the Nu number can becalculated from the following equaCon:(c) Calculate the exit temperature of the water. (d) Share your opinion on whether the use of water properties at 85°C is appropriate. Yes or No because:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.1P: 6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the...

See similar textbooks

Similar questions

6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
In a concentric-pipe heat exchanger, one of the fluids is a condensing vapour and theother is the coolant. Sketch the variation in fluid temperatures of two fluids as theyflow through the heat exchanger. Indicate clearly the inlet and outlet of the coolantand its direction of flow.
Corsidera circular smoth pipeof inner diameter D;=0.015mwhose inner surface is covered with a layer of liquid as a result of condensation. In order to dry the inner surface of the pipe, air at 300K at 1 atmis forced to flow throughit with anaverage velocity of 1.2m/s. Using the analogy between heat and mass trarsfer, detemine the mass transfer coeffícient irside the pipe for fully developed flow. Note: Viscosity of the air for given conditions is given as 1.58 x 10°n?/s. Also, for a lamirar fully developed flow the N=Sh=3.66. Your solution must state governing equations and associated assumptions, illustration and step by step execution of the overall solution
Please show all steps, not Ai generated, has been wrong before. I need to understand the process.
A shell-and-tube condenser with horizontal 7/8-in BWG 16 copper tubes is used to condense benzene vapor. The vapor is condensed at atmospheric pressure, it’s enthalpy of vaporization is around 394 KJ/kg, and the thermal conductivity at the reference temperature is around 0.150 W/m.°C. Assume the cooling water average temperature to be 40°C and neglect the tube and water film resistances. a)Calculate the reference temperature Tf and evaluate the liquid properties at this temperature. You may use the textbook and/or Perry’s Chemical Engineers’ Handbook. b)Estimate the film coefficient for the top row of tubes (W/m2.°C). c)Estimate the average coefficient for a stack of 10 tubes (W/m2.°C).
Oil at 10°C is to be heated by saturated steam at 1 atm in a double-pipe heat exchanger to a temperature of 30°C. The inner and outer diameters of the annular space are 3 cm and 5 cm, respectively, and oil enters at with a mean velocity of 0.8 m/s. The inner tube may be assumed to be isothermal at 100°C, and the outer tube is well insulated. Assuming fully developed flow for oil, determine the tube length required to heat the oil to the indicated temperature. In reality, will you need a shorter or longer tube? Explain.
Hello Sir,Good Afternoon. I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You
Milk is Pasteurized by first heating it to 71oC, and keeping it at that temperature for 17 seconds before cooing it rapidly for bottling. Fresh milk at 5oC enters the Pasteurization unit where it flows through a thin-walled stainless steel (SS) tube of 2.0 cm diameter. The inside surface of the tube is such that the flow is turbulent to promote good mixing and uniform temperature across the flow at every point along the tube. Heating is provided by passing the tube in a closed container that is filled with saturated steam at atmospheric pressure and 100oC. Hence, we can assume that the thin-walled SS tube temperature is maintained at 100oC all along its length by condensing steam over the outside surface. The flow-rate of milk is 40kg per minute (i.e. approximately 10 gallons per minute). a) What is the mean velocity (m/s) and ??? for the milk flowing through the tube between 1-2? b) What is the convective heat transfer coefficient h (W/m2K) over the inside surface of the tube? c) What…
The exchanger is of a counter flow double pipe design. The oil enters at 110°C and Jeaves t 75ec (15.82 m2) vaterat the rate of 4080 kg/h is heated from 35° to 75°C by an oil having a specific heat of 1900 JACK gers. er. Explain the Determine the area of the heat exchanger necessary to handle this load if the overall heat transfer coefficient oool 55 000 ka(h of alcohol from 66°C to 40°C using 40.000 kg/h of is 320 W/m2.K.
Flow Characterisitc (Entrance Effects) Why was there some disagreement between the actual Pitot tube velocity profile and the power law velocity profile?
Liquid L D Liquid ammonia at -20°C (rho=665.1 kg/m³ and μ = 2.361*10-4 kg/m*s) is flowing through a 35 m long section of a 5 mm diameter copper tube at a rate of 0.1 kg/s then the Reynold's number is
1. Water is flowing inside of a 3-std type K copper tube at a flow rate of 1.2 kg/s. The average temperature of the water is 50°C. Cold, dry air at a temperature of 5°C and atmospheric pressure flows outside of the tube in cross flow with a velocity of 85 m/s. Determine the UA product for this tube under clean conditions.