The exchanger is of a counter flow double pipe design. The oil enters at 110°C and Jeaves t 75ec(15.82 m2)vaterat the rate of 4080 kg/h is heated from 35° to 75°C by an oil having a specific heat of 1900 JACKgers.er. Explain theDetermine the area of the heat exchanger necessary to handle this load if the overall heat transfer coefficientoool 55 000 ka(h of alcohol from 66°C to 40°C using 40.000 kg/h ofis 320 W/m2.K.

Draw the diagram of the counter-flow heat exchanger. Write the temperature difference on the…

Nser at the rate of 4080 kg/h is heated from 35° to 75°C by an oil having a specific heat of 1900 Jke K. The erchanger is of a counter flow double pipe design. The oil enters at 110°C and leaves at 75°C Dtermine the area of the heat exchanger necessary to handle this load if the overall heat transfer coefficient is 320 W/m K. (15.82 m²] LE5000 keh of olcobol from 66°C to 40°C using 40 000 ta

Nser at the rate of 4080 kg/h is heated from 35° to 75°C by an oil having a specific heat of 1900 Jke K. The erchanger is of a counter flow double pipe design. The oil enters at 110°C and leaves at 75°C Dtermine the area of the heat exchanger necessary to handle this load if the overall heat transfer coefficient is 320 W/m K. (15.82 m²] LE5000 keh of olcobol from 66°C to 40°C using 40 000 ta

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Diesel flows at the rate of 3 kg/sec through a double pipe counter flow heat exchanger. Diesel is heated from 60degC to 75degC by a water (cp=4.187 kJ/kg-K) flowing through the tube. The specific heat of the diesel is 1.780 kj/kg.K. The water enters at 115degC and leaves at 70degC.the overall heat transfer co-efficient is 340 W/m2K. Calculate the heat exchanger area and the rate of heat transfer.
Hot oil, which enter a cross-flow heat exchanger at 200 C and leave at 100 C, are used to heat water at a flow rate of 1.5 kg/s from 30 to 120 C. The overall heat transfer coefficient based on the water-side surface area is U = 220 W/m2 . K. Determine : a) the required water surface area Ac using the NTU method(let effectiveness €=0.65). b) Ac when we change the water outlet temperature to 130Cc) discuss the effect of changing the water outlet temperature to Ac? d)draw the temperature profile along the heat exchanger
A Parallel-Flow concentric tube heat exchanger is used to condense steam at 45°C using cooling water entering at 20°C and at a rate of 1.2 kg/s. If the overall heat transfer coefficient is 1200 W/m2.K and the exchange area is 5.2 m2 , the outlet temperature of the cooling water is(Take for cooling water cp=4180 J/kg.K)
It is desired to heat 230 kg / h of water from 36 to 94 ºC with oil (Cp = 2.1 kJ / kg ºC) that has an initial temperature of 175 ºC. The oil mass flow is also 230 kg / h. It has a double tube exchanger in parallel, with a total heat transfer coefficient of 570 W / m2 ºC. Calculate the total surface area of the heat exchanger.
A shell &tube heat exchanger has 4 tube passes. Oil inters to the tubes with 100oC . Mass flow rate of the oil is 3 Kg /s and its heat capacity is 2.1 Kj/KgoC. In the shell side air passes with 2 Kg /s Mass flow rate and 1.009 Kj/KgoC heat capacity. Input temperature of air is 20 oC and output temperature is 80 oC. Overall heat transfer coefficient is 200 W/m2 oC. Considering outer diameter of tubs 2cm and tube length 2 m, determine number of tubes in each pass
310 m algunaourtsdi bayon bozu (A) In a food processing plant a brine solution is heated from 6°C to 12°C in a double pipe heat exchanger by water entering at 50°C and leaving at 40°C at the rate of 0.166kg/s. If the overall heat transfer coefficient is 850 W/(m².K), what heat exchanger area is required for (1) parallel flow heat exchanger and (2) counter flow heat exchanger. Discuss the results?. Take C₂ (for water)= 4.180 kJ/kg.K mbmeod (isolev si ma do liw novel
Please answer all parts or leave for someone else to answer i will give you a very positive feedback.
helpp
A 95kg/hr hot fluid is used to heat a cold fluid from 10oC to 70oC using a double pipe heat exchanger (DPHE). The hot fluid enters at 205°C and leaves the DPHE at 108°C. The Cp of hot fluid is 1.10 kcal/kg°C and the Cp of cold fluid 0.95 kcal/kg°C. a) Calculate the LMTD if the the flow is cocurrent in oC b) Calculate the LMTD if the the flow is countercurrent in oC
he shell fluid,ethylene glycol, enters at 120oC and leaves at 60oCwitha flow rate of 4000 kg/h. Water flows in the tubes, entering at 35oCand leaving at85oC. The overall heat-transfer coefficient for this arrangement is 900W/m2·oC.The exchanger is a shell tube with two shell passes and two tube passes.Calculate the following: a) The water exit temperature if flow rate of glycol to the exchanger is reduced in half with the entrance temperatures of both fluids remaining the same and by how much is the heat-transfer rate reduced?; b) The percentage reduction of heat transfer if water-flow rate is reduced by 25percent,while the gas flowrate is maintained constant along with the fluid inlet temperatures. Assume that the overall heat-transfer coefficient remains the same; andc) The flow rate of water required andthe area of the heat exchanger;
need all part answers
A long, thin-walled double-pipe heat exchanger with tube and shell diameters of 0.01 m and 0.025 m, respectively, is used to condense refrigerant-134a with water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi= 4100 W/m² °C. Water flows through the shell at a rate of 0.3 kg/s. The thermal resistance of the inner tube is negligible since the tube material is highly conductive and its thickness is negligible. Both the water and refrigerant-134a flows are fully developed. Properties of the water and refrigerant-134a are constant. Water properties: p = 998 kg/m³, v=u/p-1.004x 10-6 m²/s, k = 0.598 W/m. °C, Pr = 7.01 Cold water D Do