concentric-pipe heat exchanger, one of the fluids is a condensing vapour and the other is the coolant. Sketch the variation in fluid temperatures of two fluids as they flow through the heat exchanger. Indicate clearly the inlet and outlet of the coolant and its direction of flow.

Q: Air at 1 atmosphere and a temperature of 60 F enters 1/2-in. id tube with a velocity of 80 fps. The…

A:

Q: A DPHX is made of a 6-nom sch 40 commercial steel outer pipe and a 5-nomsch 40S stainless steel…

A: Heat Transfer: According to the second law of thermodynamics, heat is always transferred from a…

Q: -1 Oil with speed 7260 kg / h and heat capacity c (oil) = 2.07 kJ kgrK cooled from 394.3 K to 338.9…

A:

Q: C- A fluid flowing in a tube with long (L) and diameter (D) at mean flowing velocity of (Vm). show…

A:

Q: A two effect system of evaporators with parallel forward feed flow of liquid and vapor is to be…

A:

Q: 33. Water at 25 C flows in a smooth tube, having a diameter of 5 cm, at a rate of 1 kg/s. The tube…

A:

Q: ith constant angular velocity @. Taking into consideratic erature and surface heat flux at the…

A:

Q: 1. By increasing the flow rate, the overall heat transfer coefficient increases? Explain.

A: Solution o question (1) as per our company policy:

Q: Across-flow exchangerwith both fluids unmixedand an airflow rate of 0.5 kg/s on bothsides. The hot…

A: given; ⇒mass flow rate (m)=0.5kg/s⇒hot air inlet temperature (Thi)=3500c⇒hot air outlet temperature…

Q: Bourdon tube is also referred to as an

A:

Q: For laminar flow in a round pipe of diameter D, at what dis- tance from the centerline is the actual…

A: INTRODUCTION : Reynold's number is less than 2000, the flow through a circular pipe will be viscous…

Q: Steam condensing at 120°C (h = 2203 kJ/kg) on the shell side of (1 shell and 12 thin- walled tubes)…

A:

Q: Blowing air from 3 separate vents to a car gallery where the indoor air temperature is 22 °C and the…

A:

Q: 3. Two parallel plates are separated by a distance 2H. The plates are moved in opposite directions…

A:

Q: Discussion Explain how the stationary fluid flours when it becomes in touch with heated wall. You…

A: Stationary Fluid flows when in contact with heated wall. This is a fluid mechanics problems related…

Q: A 6-cm diameter pipe is used to deliver hot water to a residence. A 8-m-long horizontal section of…

A: Given    The mass flow rate of water, m = 0.015 kg/s

Q: The value of the Log Mean Temperature

A: Given; Determine the LMTD ?Where, Saturated steam at 1000 C It condenses on the outside of a tube.…

Q: What is the pressure drop that arises from a Lid-driven cavity flow?

A: A Lid-driven cavity flow refers to the motion of a fluid contained within a square or rectangular…

Q: As part of an industrial pipe system a 6-meter-long by .5 meter inner diameter copper pipe weighing…

A:

Q: Q2. Forced convective heat transfer coefficient depends on type of flow (True/False)

A:

Q: Determine the transfer coefficient for water flowing through a 1-inch pipe. inch, 16 BWG and 3 m /…

A:

Q: A fluid flowing in a tube with long (L) and diameter (D) at mean flowing velocity of (Vm), show that…

A: Write the head loss per unit length of the pipe. S=∆PρgL        ...... (1) Again, write the another…

Q: Air at p = 1 atm enters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet…

A: To find: The heat rate entering the tube. Given: The diameter of the tube is d=5 mm1 m1000 mm=0.005…

Q: Explain Mass and energy flow rates associated with the flow of steam in a pipe of inner diameter D…

A:

Q: 21. In a repair shop compressed air is used to operate pneumatic tools. The total length of the…

A: Given Data The total length of the airline is:L=500 ft The inner diameter of smooth pipe is:I.D=0.5…

Q: With the pipe system in the figure, the water taken from a very large reservoir is poured into the…

A:

Q: C Hot air enters a sheet metal duct located in a basement. Determine the exit temperature and the…

A:

Q: A hot fluid passes through a thin-walled tube of 10-mm diameter and 1-m length, and a coolant at T =…

A: Need to determine the outlet temperature.

Q: Air at p = 1 atmenters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet temperature…

A:

Q: solve both, show assumptions

A: Answers are given below:Explanation:

Q: Flow Characteritistics( Enternce Effect) Why was there some diagrement between the actual Pitot…

A: This article reports on one component of a larger study on measurement of the zeropressure- gradient…

Q: Not Ai generated answers, I need to understand please show all steps.

A: Please refer below page.If you have any questions feel free to ask.Explanation:

Q: A constant heat flux q = 200 W / m2 is applied to a circular section pipe with a diameter D = 50 mm…

A:

Q: an oil at average temperature of 100 F flows at 1.2 ft/s velocity 0.834in inside diameter horizontal…

A: Given data average temperature of oil, Toil=100 F (310.9K) V=1.2 ft/s D=0.834 in average surface…

Q: It is desirable to derive a relation for the fully developed laminar flow rate, slug flow (flow,…

A: Given: Fully developed laminar flow rate,

Q: 09:48 Today Edit 09:44

A:

Q: Flow Characterisitc (Entrance Effects) Why was there some disagreement between the actual Pitot…

A: Concept of fluid mechanics used

Q: Estimate the leakage through the wall per

A: Given; A=4.6 m× 2.3 mX1=115 mm=0.115 mX2=75 mm=0.075 mX3=25mm=0.0025mT1=291 KT2=271…

Q: Please help. I am not sure how to approach this problem. This problem involves heat transfer and…

A: Step 1:Step 2:Step 3:Step 4:

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.