Determine the minimum applied force P required tomove wedge A to the right. The spring is compressed adistance of 175 mm. Neglect the weight of A and B. Thecoefficient of static friction for all contacting surface is μs= 0.35. Neglect friction at the rollers.k ==15 kN/mPAB10°

Answered: Determine the minimum applied force P…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.49P

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The uniform cylindrical drum weighs 250 lbs and is supported by a frictionless roller at A and the frame at C. The coefficients of friction between the frame and the drum at C are as follows, static coefficient u: = 0.3 and kinetic coefficient uk = 0.25. If the drum is at rest, find M required to start the drum moving? For full credit show a labeled free-body diagram. 2' 30°
Calculate the horizontal force P on the light 14° wedge necessary to initiate movement of the 58- kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.23. Also determine the friction force Fg at point B. (Caution: Check carefully your assumption of where slipping occurs.) 58 kg B P > 149 Answers: P = i FB = i N
Find the value s so that the worker can climb the ladder without causing it to slip. The weight of the worker is 90-kg and neglect the weight of the ladder. The ladder has a small roller at the top and at the ground the coefficient of static friction is 0.25. The center of mass of the worker is directly above her feet. B 4 m 1.5 m
answer all the question with the steps please
I want also the reference please.if you know
M. 0.3 m The block brake is used to stop the wheel from rotating when the wheel is subjected to a couple moment. Determine the smallest force P that should be applied as well as the magnitude of the corresponding reaction force at support C. Use the couple moment Mo = 430 N-m, the coefficient of static friction between the wheel and the block of 0.6, a = 1.8 m, b = 0.8 m, and c = 0.075m. Round all answers to the nearest integer. The smallest force P that should be applied is: N. The magnitude of the reaction force at support C is: N.

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L