Need help! Position To0.3AB2X010 ±0.2 20 10.500.15A BAD0.252X 45°0.1AB0.25 AAUXILIARY VIEWB0.3A BNOTES:1. UNLESS OTHERWISE SPECIFIED ALL ANGLES ± 5°2. Describe the tolerance zone for the angularity tolerancelabeled "D."3. Describe the effect of the modifier in the angularitytolerance labeled "D."4. Which geometric tolerance could be used in place ofthe angularity tolerance labeled "A" that would resultin the same requirement?A. PerpendicularityB. ParallelismC. CylindricityD. None of the above5. Is the angularity tolerance labeled "A" a standard-com-pliant specification?If no, explain.6. Is the angularity tolerance labeled "B" a standard-com-If no, explain.pliant specification?7. Is the angularity tolerance labeled "C" a standard-com-pliant specification?If no, explain.8. Is the angularity tolerance labeled "D" a standard-com-pliant specification?sotsolbri faib AIf no, explain.

Answered: Image /qna-images/answer/0dbd3bb3-b2b8-41f2-8e8c-fa825f71228c.jpg

Answered: Position To 0.3 AB 2X010 ±0.2 20 10.5…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Complete the two charts below showing the perpendicularity tolerance for the different pilot sizes. Also fill in the virtual size for each of the parts. Hint- Lookout for M modifier
I require a gap of .03 min and .06 max between the 2.50 dim and the B dim (at the bottom). I apply a +/- .01 tol to the 2.50 dim. The upper and lower limit of B dim is 2.47/2.44 True or False?
Please Fill In the blanks where I have marked red X's using the questions and Image below. 1. On the drawing above, before any geometric controls are applied, what is the coaxility tolerance is implied between the diameters? 2. On the part above, apply datum feature symbols to create a datum axis A-B by using the right and left diamters. 3. Apply a position coaxility between the right and left diamter of 0.1 at MMC. 4. Apply a position tolerance to the large center diameter within a diameter of 0.3 in relation to the single datum axis established by both datum features A and B.
I need this part answered according to the disrections provided in the image.
Please answer allquestions
13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance. 20. Refer to the figure below. Read the feature control frame in the figure and write it out below. Ø 010M ABMCM
a) Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a= 1.500 ± 0.001 in b= 2.000 ± 0.003 in c= 3.000 ± 0.004 in d= 6.520 ± 0.010 in Determine the mean gap ￣w and its tolerance. Determine the mean size of d that will assure that w ≥ 0.010 in. b) A 1-in-diameter rod, 3 ft long, of unknown material is found in a machine shop. A variety of inexpensive nondestructive tests are readily available to help determine the material, as described below with results in bracket: i. Visual inspection. (Dark gray, rough surface finish, moderate scale) ii. Check if it is attracted to a magnet. (Yes) iii. Measure Weight. (7.95lbf) iv. Inexpensive bending deflection test: Clamp one end in a vise, leaving 24 in cantilevered. (5/16in) v. Brinell hardness test. (HB = 200)
Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance.
I need help please. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the resultant tolerance zone and virtual size on the sketch of the produced part below. The image and question are also attached.
On drawing 31A059, what is dimension F? All
How many auxiliary views are found on this print?
Hello Sir.Good Night. I have a question in my homework related geometry tolerance lesson. The following below is my question. Please advice. Thank you

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS