Please can you help me with the attached question? Neutron diffraction is used to measure the strain in threedirections parallel to the x, y and z directions within anickel forging. The values of x = 0.46 × 10-3,=દક્ષુ -0.01 × 103 and ε₂ =-0.026 × 10-3 areobtained. With mechanical properties of E = 200 GPa=and vdirection.0.29, calculate the residual stress in the xGive your answer in MPa to 3 significant figures.

Answered: Neutron diffraction is used to measure…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Whats the answer for this please ?
6. A ceramic part for a jet engine has a yield strength of 648 MPa and a plane strain fracture toughness of 8.49 MPam 4. To be sure that the part does not fail, we plan to ensure that the maximum applied stress is only one-third of the yield strength. We use a nondestructive test that will detect any internal flaws greater than 0.27 mm long. Assuming that the Y constant is 1.4, does our nondestructive test have the required sensitivity? Explain.
A ceramic part for a jet engine has a yield strength of 66,215 psi and a plane strain fracture toughness of 5000 psi (in) ¾. To be sure that the part does not fail, we plan to assure that the maximum applied stress is only one-third the yield strength. We use a nondestructive test that will detect any internal flaws greater than 0.05 in. Iong. Assuming that f = 1.2 , does our non- destructive test have the required sensitivity? Type 1 for yes and O for no.
Pravinbhai
I am not reallyunderstanding what this problem wants with the wording, coud you help me clarify that please? Thank you so much!!
tensile test is performed to determine the parameters strength constant C and strainrate sensitivity exponent m for a certain metal. The temperature at which the test is performed = 500°C. At a strain rate = 10/s, the stress is measured at 140 MPa; and at a strain rate = 150/s, the stress = 280 MPa. (a) Determine C and m. (b) If the temperature were 600°C, what changes would you expect in the values of C and m?
If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.
Problem 2.11 3 of 7 > I Review Part A The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 450 mm, H= 345 mm, di = 3 mm, d2 = 5 mm, dz = 11 mm, d4 = 9 mm, d, =1 mm, and d6 = 4 mm. Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. μΑ ? (Yc)ry = Value Units Submit Request Answer Figure 1 of 1 Part B dz Determine the shear strain Yry at corner D d. Express your answer to three significant figures and include appropriate units. di B μΑ ? H (YD)zy = Value Units L d. Submit Request Answer P Pearson
A steel plate, which has a fracture toughness in a plane strain state of 83 MPavm, is alternately loaded in tension at 750 MPa and in compression at 20 MPa. The plate must survive 15 years with the stress applied at a frequency of once every 3 min. Calculate the constant C of the material if n=2.8 . Assume that the geometric factor f=1 for all your imperfections. Internal imperfections have a size of 0.0015 mm
A ceramic part for a jet engine has a yield strength of 75,000 psi and a plane strain fracture toughness of 5,000 psiVin. To be sure that the part does not fail, we plan to ensure that the maximum applied stress is only one-third of the yield strength. We use a nondestructive test that will detect any internal faws greater than 0.05 in. long. Assuming that f = 1.4, does our nondestructive test have the required sensitivity? Explain. A manufacturine proorssthat unintention
For a tensile test it can be shown that the percent cold work (%CW) is related to strain according to the following relationship: %CW=(εε+1) × 100 Using this equation, compute the percent cold work experienced by naval brass (for which the stress-strain behavior is shown in the Animated Figure 6.12) when a stress of 415 MPa (60190 psi) is applied.
A strip of metal is originally 5 m long. It is stretched in 3 steps: first to a length of 6 m, then to 7 m and finally to 8 m. The original cross section area of the metal strip is 40 mm?. Compute the final cross section and find the percentage reduction in area due to the above stretching process. Also calculate the force required for the final stage of stretching, assuming that the true stress true strain relation for the material is given as o = 700 0.48 MPa. 5 (c)

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS