A 100 m length of a smooth horizontal pipe is attached to a large reservoir. Aattached to the end of the pipeto pump water into thereservoir at a volume flow rateof 0.01 m³/s. What pressure(gage) must the pump produceat the pipe to generate thisflow rate? The inside diameterof the smooth pipe is 150mm.Dynamic Viscosity of water is1*103 Kg/(m.s). K at the exitof the pipe is 1.pump10 mD=150mmL= 100 m-Pump

Detailed explanation:Note: the entrance loss in the container is ignored due to very small value…

Answered: A 100 m length of a smooth horizontal…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Pitot tube in a pipe in which air is flowing is connected to a manometer containing water asshown below. If the difference in water levels in the manometer is 10 cm, what is the velocity of flow in the pipe? Assume a tube coefficient of Cp = 0.99, specific weight of air is 12 N/ sq.m.
The Water is flowing through a pipe having diameter 350 mm and 210 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 25.85 N/cm? and pressure at the upper end is 11.6325 N/cm? & the rate of flow through the pipe is 40 lit/s. Draw a neat diagram and determine the following: 1.Velocity head at bottom of the pipe in m/s. 2. Velocity head at top of the pipe in m/s. 3. The difference in datum head between top & bottom in meter of water - 4. The difference of pressure head between bottom to top end in meter of water.- The velocity of flow of water at the bottom in m/s.
In some high-rise buildings, water is stored in an elevatedtank on the roof to minimize pressure fluctuations inthe system. Consider water that is pumped through a 10-cmsteel pipe to the roof of a 200-m-tall building; the pump ison the ground floor. For a water temperature of lOOC and aflow of 0.02 m3/s, what is the pressure at the pump discharge(in kPa)?
7:23 M When the level in the tark is 10 m above the centerlire of the outlet, how fst is the level in the tank falling? WouH 10 m (3) Weaeofferedsomepipes madeof arnew kindof plastic. Totest their roughress, we pump water throgha 0.0762 m pipe made of this material atanaverage velocity of 12.19 m/s The dbserved Faning friction factor is 0.0032. Estimate the absolute rougnessof this pdastic. (4) What pressure drop is required in order to pump water at 20°C through a pipe 25 am in diameter and lengh 1234 m at arte of 1.97 m2 sec? The pipe is harizrtal and contains four stadrdradius 90° elbows and two 45° elbows. (A standard-radius 90° elbow isroughly equivalert to the resistance offered by apipeof length 32 diameters a 45° elbow, 15 diameters) (5) Cansider the steedy-state flow of animompressible Newtonian fluid througha hrizartal tube f irner radius Radlength L, sshown belpw: Findthe velocity distribution in the liquid Neglect end effects. Page|2 End I Recommended Share Extract Pages…
Two piezometers (manometers) are placed 1.5m apart in a horizontal plastic pipe as shown in figure. What is the difference in water level (cm) between the two manometers when the flow rate in the pipe is 0.0004 m /s? Fluid in pipe is water. Pipe diameter 2.5 cm. Density=1000 kg/m. Viscosity = 0.001 Pa-s. %3D 0.25 5.74 log 10 Re 09 | Water
An incompressible fluid (density 1000kg/m3) is flowing through a pipe with a constriction. The pipe is on an angle of 30 degrees with the narrow section at at distance of 10m from the wide section and lower that the wide section . The speed of the fluid in the wide section is 2m/s and 10m/s in the narrow section, I f the pressure in the wide section in 250 kPa. What is the pressure of the fluid in the narrow section ?
Only handwritten no Chatgpt.
The thrust of a shaft is taken by a collar bearing provided with a forced rication system. The lubrication system maintains a film of oil of ilerm thickness between the surface of the collar and the bearing The aemal and intemal diameters of collar are 16 and 12 cms respectively. The thickness of oil film is 0.02 cms. and coefficient of viscosity is 0.91 poise. Find the horse-power lost in overcoming friction when the shaft is ntated at a speed of 350 r.p.m. Skult.
What must the gauge pressure p be at A if the volume flow rate out of the pipe at point B is 0.0800 m^3/s?
show all working out please
I need correct ans with step by step method
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS