Find the solution of the following Differential Equations1)"-4y+3y=03) "+16y=02) y"-16y=04) y"-y-6y=05) y"+2y=07) y"+y=0, (#0)9) y"-y=0, y(0) = 6, y'(0) = -411) y"-4y+3y=0, y(0)=-1,13)y'(0) = -5"+2y+2y=015) y"-9y=017) y"-4y=06) y"-2y+2y=08)"+4y+5y=010) y"-9y=0, y(0) = 2, y'(0) = 012) y"-3y+2y= 0, y(0)=-1,y'(0) = 014) 4y+4y+y=016) "+6y+12y=018) 4y+4y+17y=0

Answered: Find the solution of the following…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

0.8 m wo B D E 0.8 m 1.0 m Bar AB rotates about the fixed point A with constant angular velocity wo. The system starts with bar AB horizontal. 1) Use the relative velocity equation to find the velocity of C in terms of the angles 0 and > and their derivatives. 2) Determine the lengths of bars AB and BC so that as bar AB rotates, the collar C moves back and forth between the positions D and E. A design constraint is that bar BC must be longer than bar AB (as shown in sketch). 3) You are given the design constraint that the magnitude of the acceleration of collar C must not exceed 200 m/s². What is the maximum allowable value of wo? 4) Create the following plots for a complete revolution of bar AB using the values for lengths and angular velocity determined above: о о e and > versus time as 2 sub-plots. Position, velocity, and acceleration of C versus time as 3 sub-plots. Velocity and acceleration of C versus its position as 2 sub-plots. - 5) Use your plotted results to describe the…
please answer question 3 , 5, 7 in full detail explanation
The kinematic diagram is given as 012=60 degree and the speed of the mechanism is constant and 012=50 rad/sn in the slide mechanism whose limb dimensions are given below. Find the following items. AoA = r2 = 0.2 m A,Bo = r1 = 0.5 m 012 = 60° 12 = 50 rad/s %3D %3D A a) Write the vector closure equations b) Bring the vector closure equations into scalar form c) Find s13,014 d) Find s13,014 e) Find 513,014 S13 014 ri Bo 012 Ao
20- An athlete is running in a parking lot on which the coordinate axes are drawn. The coordinates of the athlete's position are given as x=-0.31t^2+7.2t+28 and y=0.22t^2-9.1t+30 as a function of time t. Find the magnitude of the athlete's acceleration vector a (m/s2) at t=15s. A) 1,98 B) 0,58 C) 1,23 D) 0,76 E) 1,45
Part b
how to solve the question attached
What do crossed and open mean? Please explain exactly on this drawing only and when it is crossed and open? and When do we decrease 360 and when do we increase 360? with all explination on the graph only i will give u good feedback please
Can someone please help me to solve this graphically on CAD as well as analytically. Show all work thank you!
In Problem 1 use Euler’s method to obtain a four-decimalapproximation of the indicated value. Carry out the recursion of(3) by hand, first using h= 0.1 and then using h= 0.05 (show all steps) 1) y'=2x-3y+1 y(1)=5; y(1.2)
what is the possible solution to theta3 in degrees?
A simply supported shaft arrangement is shown in the figure. A solid shaft of 50 mm diameter made of low-carbon steel is used. Given values are: X;=762 mm X:=1016 mm X3=508 mm PA=356 N Ps=534 N Solution: Determine first critical speeds: a) 1155 rpm b) 648 грm a) Unloaded shaft b) Rayleigh method с) 651 грm c) Dunkerley method
Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000 lb/in2 (psi)Calculate a cubic function (3rd order polynomial – Ax3+Bx2+Cx+Constant)Use this function to create a function that describes the slope of the cubic function (the derivative of thecubic function). This new function allows you to calculate the tangent to any point along the curve. Thetangent is the modulus of elasticity (E). The concrete code provides a formula to calculate E for concrete. That formula is:E = 57,000√??′, where f’c is in units of psi, and E is in units of psi.Use the derivative function you calculated to locate the point on the curve where the slope of the curvematches E using the concrete code formula. Express that stress point on the curve as a percentage ofthe compressive strength of the concrete. Now, calculate the secant modulus for the test case using 1,500 psi (50% f’c) as the arbitrary point onthe curve.Assume fracture occurs at the last point…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS