I need help please.Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the resultant tolerance zone and virtual size on the sketch of the produced part below.The image and question are also attached. applied.13.513.211. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw theresultant tolerance zone and virtual size on the sketch of the produced part below.to SicuereB1320.5

Answered: Image /qna-images/answer/17093565-4c08-4e28-816f-79ace87c5743.jpg

Answered: 13.5 13.2 11. Apply a dia 0.5 at MMC…

13.5 13.2 11. Apply a dia 0.5 at MMC straightness control to the axis of the part above and draw the resultant tolerance zone and virtual size on the sketch of the produced part below.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Chapter 3: 13. What type of geometric tolerance has no datum features? 14. A theoretically exact dimension is called a 15. The feature symbol specifies that a group of two or more interrupted features of size are to be considered one single feature of size. 16. For an individual regular feature of size, no element of the feature shall extend beyond the maximum material condition boundary (envelope) of perfect form. This statement is the essence of 17. What is the name of the symbol used to identify physical features of a part as a datum feature and must not be applied to centerlines, center planes, or axes? 18. The is the condition in which a feature of size contains the maximum amount of material within the stated limits of size. 19. The total positional tolerance equals the sum of the tolerance and the tolerance.
U copy from anywhere I need answer only step by step
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative…
Hello Sir.Good Night. I have a question in my homework related geometry tolerance lesson. The following below is my question. Please advice. Thank you
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. Please refer to the attached image.
I need help answering this quick review pertaining to the print provided.
1. How is the location tolerance of Position different from the other 11 GD&T tolerances? Pick two (2) other tolerance and contrast write about those two in detail relative to Position tolerancing. 2. Form tolerances, elaborate how they are different from Orientation tolerances
Need Help on both Questions.
For a 10 H7/p6 fit