The answer to the problem is 7.24 N. Please show me how to get the final answer A long massless cord is wrapped around the periphery of the cylinder, as shown. Thecylinder has a mass m = 2.4 kg, radius r = 0.3 m, and a radius of gyration = 0.2 mabout its mass center G. If the cylinder is released from rest, the initial tension in the cordis most nearlyA. 23.8 NB. 20.3 NC. 18.5 ND. 15.3 NE. 12.8 NF. 10.2 NG. 7.24 NH. 5.00 NI. 3.19 NJ. 2.40 Nrm, kG

Here is the step-by-step explanation:Given:Mass of the cylinder, m=2.4kgRadius, r=0.3mRadius of…

Answered: A long massless cord is wrapped around…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The centroidal mass moment of inertia ofthe pulley assembly is 20 ft-lb-s2. Determine (a) the tension in the cordsupporting 161-lb block , (b)the tension supporting the 322-lb block, and (c) the angularacceleration of the pulley system .Hint: Determine first the direction ofmotion, i.e. will block A move up ordown?
Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis through G of 3.0 ft. The bar is supported by the cords AB and CD which rotate in the same vertical plane. The speed of the mass centre, when in the position shown, is 12 fps. Determine the tension in cables AB and CD for this position.
The 154-kg wheel has a radius of gyration about its center O of ko = 280 mm, and radius r = 0.4 m. When the wheel is subjected to the constant couple moment M = 73 N•m, it starts rolling from rest. Determine the mass moment of inertia lc (in kg. m²) about the wheel's /C. Please pay attention: the numbers may change since they are randomized. Your answer must include 1 place after the decimal point. Take g = 9.81 m/s². M Your Answer: Answer ...
The double pulley shown has a mass moment of inertia of 15 Ib-ft-s^2 and is initially at rest. If the inside radius is 9 in., determine the magnitude and direction of angular acceleration of the pulley. 460 lb 300 lb
cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (2) The mass moment of inertia of the spool about point A _______(kg·m2)(two decimal places)
The moment of inertia for an extended body is I = [r² dm. Prove that for a circular disc of mass M and radius R the moment of inertia, about an axis through its centre, is I = MR². A 80-kg man stands still on the rim of an initially stationary circular carousel of radius 3 m and mass 200 kg. The man begins to walk at 1 ms-1 (with respect to the ground) along the rim. What is his angular velocity, w? What is his angular momentum? What is the angular velocity of the carousel? How fast is the man walking with respect to the carousel?
2) A slender uniform 30 kg bar is hinged off center and swings down on a vertical plane. In the configuration shown the angular speed of the bar is @ = 2 rad /s?. Knowing that the length of the bar is = 8m, the mass moment of inertia about the center of mass G is IG = mbl² 1 12, and the distance between G and O equals 2m, determine the force at the smooth hinge O. 30°
I need the answer as soon as possible
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
Consider a disk of radius R = 0.2 m, mass of mc = 20 kg, and moment of inertia of IG= 0.40 kg-m² mounted on a ball bearing joint at point G. The disk has a a cord wrapped around its perimeter. A cylinder of mass mg = 6 kg hangs from the other end of the cord and is moving at VB (t₁) = 2 m/s downward at the instant shown (time t₁). Three seconds later, at time t2, what is the tension T and the velocity of the cylinder? (Hint: Use linear momentum-impulse applied to the cylinder and angular momentum-impulse applied to the disk. Evaluating with the data given T = 36.78 N and vB (t2) = -13.036 m/s.) DISK motion VB (t₁) ↓2 R 70 G Jllllls MG, + A - B IG cord Cylinder тв
The drum shown in Fig. (a) has a radius of gyration of 30 cm and weights 1,8 kN. It is supported by means of small hubs which rest in bearings. A weight of 1 kN is attached to one end of a rope, the other end being wrapped around the drum. Neglecting friction in the bearings, determine the acceleration of the weight, the angular acceleration of the drum, and the tension in the rope. 37.5 cm 1.8kN T IkN
A 96.6 lb is fastened to a cord which is wrapped around a solid cylinder of 3ft radius weighing 322 lb. The cylinder rotates about its horizontal and centroidal axis. What torque applied to the cylinder will raise the weight with an acceleration of 12ft per second? What will be the total bearing reaction?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS