A 96.6 lb is fastened to a cord which is wrapped around a solid cylinder of 3ft radius weighing 322 lb. The cylinder rotates about its horizontal and centroidal axis. What torque applied to the cylinder will raise the weight with an acceleration of 12ft per second? What will be the total bearing reaction?

Q: Q4. As shown in the image below, a force of P= 310 N is applied to the 64-kg cart. The dimensions…

A: To find : To find the total normal reaction at the wheel A. Given :   force P=310 N…

Q: 2. For this series of 4 questions, a man sits in the chair which is pin-connected to the 10-m frame…

A: Given data: v=4.5 m/sat=0.1 m/s2R=10 m Need to determine the magnitude of the total acceleration.

Q: The uniform 24-m robotic arm OB weighs 300 kg and is hinged at its lower end to a fixed support at…

A: Length of arm = 24 m Weight of OB = 300 kg Starting Torque = 1300 Nm   To find out :- Tota force…

Q: Because of the way in which the mass is distributed, wheel A has a radius of gyration of 0.65 m and…

A: For each wheels A and BRadius of the wheel A and B is RA= RB=1m Given mass of Wheel A and B…

Q: The uniform 10-lb disk pivots about a well-lubricated axel at O. A 4-lb slender bar is rigidly…

A: To Find :  The maximum angular velocity the disk achieves, Given :  The weight of uniform disc is…

Q: 2. The 4-m boom shown has a mass of 60 kg and is pinned to the back of the truck at point A and…

A: Data given -

Q: 40-kg cylinder is hung from the gear system shown. Gear s a mass of 8 kg and a radius of gyration…

A: Given,

Q: A wheel of mass M has radius R. It is positioned vertically on the floor and you exert a horizontal…

A:

Q: The shown 61 lb spool of radius R = 1.5 ft has a centroidal radius of gyration ko = 0.7 ft is…

A:

Q: 10" 6" D - - 9 lb 10° Y

A: Given,

Q: An object of mass 40 kg has a radius of 0.2 m. If the surface is tilted, there is enough friction…

A: Question is solved below.Please give helpful rating.Explanation:

Q: The 0.4 kg B pin in the figure moves freely inside the circular slide DE with radius b and the…

A: Solution:

Q: An excavator encounters a reaction force of 7600 lb from the ground, normal to line AC, as shown.…

A:

Q: 2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: The drum shown in Fig. (a) has a radius of gyration of 30 cm and weights 1,8 kN. It is supported by…

A: Given data: k=30 cmw=1.8 kJW=1 kNr=37.5 cm Need to determine the angular acceleration of the drum.

Q: The assembly shown weighs 12 lb and consists of 4 thin 16-in.- diameter semicircular aluminum plates…

A: Using the second rotational kinematic equation, Here, θ represents the angular displacement, ωo…

Q: The 13-kg wheel is rolling under the constant moment of M= 89 N-m. The wheel has radius r= 0.47 m,…

A: Gg

Q: Two beams are joined end to end and hinged at the left end.  The left beam has a mass of 10 kg and…

A: Given data, mL = Mass of the left beam = 10 Kg mR = Mass of the right beam = 12.2 Kg To determine,…

Q: 1372. The unbalanced wheel shown in Fig. P-1372 weighe 322 Ib and hasa mas radius of Kyration of…

A:

Q: he 15-lb bar BC is connected to a disk centered at A, and to a bar DC. If the disk is made to rotate…

A: Given data as per the question weight of BC bar =15 lb Length of BC =30 in

Q: The bar AB is uniform and has a mass of 50.0 kg.  At the moment shown, the rod has an angular…

A: Given that, Mass of bar AB = 50 kg Angular velocity of rod = 4 rad/sec Spring is stretched by 0.3 m

Q: Suppose a 30 lb truck wheel 18 in. in diameter has a radius of gyration of 4 in. and  the 6120 lb…

A: Given: The mass of the truck wheel is mw=30 lb132.2 ft/s21 ft12 in=0.07764. The diameter of the…

Q: M Co r

A: Given,

Q: Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis…

A:

Q: The 8.0-lb bar is pinned at its center O and connected to a torsional spring. The spring has a…

A:

Q: A force of P = 20 N is applied to the cable, which causes the 175-kg reel to turn without slipping…

A:

Q: The 16-kg wheel is rolling under the constant moment of M = 60 N-m. The wheel has radius r= 0.50 m,…

A:

Q: A wheel is attached by a cable to a block  The wheel has a radius of 2ft and weighs 300lbs, the…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.