30. Repeat Problem 28, except using a shaft that is rotating and transmitting a torque of 150 N·m from the left bear- ing to the middle of the shaft. Also, there is a profile key- seat at the middle under the load. 28. The shaft shown in Figure P5-28 is supported by bear- ings at each end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as pos- sible while keeping the stress safe. Determine the required d 20 mm 5.4 kN d D = ? Length not to scale -α = = -125 mm 20 mm a = -250 mm- FIGURE P5-28 (Problems 28, 29, and 30)

30. Repeat Problem 28, except using a shaft that is rotating and transmitting a torque of 150 N·m from the left bear- ing to the middle of the shaft. Also, there is a profile key- seat at the middle under the load. 28. The shaft shown in Figure P5-28 is supported by bear- ings at each end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as pos- sible while keeping the stress safe. Determine the required d 20 mm 5.4 kN d D = ? Length not to scale -α = = -125 mm 20 mm a = -250 mm- FIGURE P5-28 (Problems 28, 29, and 30)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
28. The shaft shown in Figure P5-28 is supported by bear- ings at each end, which have bores of 20.0 mm. Design the shaft to carry the given load if it is steady and the shaft is stationary. Make the dimension a as large as pos- sible while keeping the stress safe. Determine the required d = 20mm D = ? R = ?| 5.4 kN d=20mm Length not to scale -a = ?- +а= a = ? + -125 mm- -250 mm- FIGURE P5-28 (Problems 28, 29, and 30)
A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.062° for good bearing life. Check wether the shaft dia below meets the requirement. If not determine a suitable shaft diameter. 400 mm FB 350 mm 25° 300 mm FA = 11 kN• 20° 50-mm dia. Gear A, 600-mm dia. Gear B, 300-mm dia. mm. The minimum shaft diameter is determined to be
A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20 pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum slope specification of 0.064" for good bearing life. Does the dia shown below meet the requirement? if not determine a suitable shaft diameter. 1.25-in da Gear A F₁-300- Gear B Sindia The minimum shaft diameter is in.
Solve with numerical steps
Please help with all need items, analysis, element, mohir circle, wtc. Thank you.
The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a speed of 400 rpm and the sprocket has a pitch diameter of 6 inches. The shaft is made of ASTM-A 709 Grade 50 steel. A factor of safety of 2.5 is required. Is the design acceptable? Hint: You need to calculate torsion and bending stresses during solution.
Solve part b,c and d only
A,B,C,D,E,F,G WHICH POINT PLS WRITE THE LETTER AS UR FINAL ANSWER THX
Required information The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. ↑ i 3 in- -10 in- F₁ ↑ in F₂ -10 in- All fillets in R. -8 in inៗ → p'in 3 in in B -3 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the factor of safety against fatigue at infinite life? Use the Goodman failure criterion. (You must provide an answer before moving to the next part.) The factor of safety against fatigue at infinite life is
pls help ASAP
Figure P4–49 shows the end of the vertical shaft for a rotary lawn mower. Compute the maximum torsional shear stress in the shaft if it is transmitting 7.5 hp to the blade when rotating 2200 rpm. Specify a suitable steel for the shaft.