gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force 4 applied at the 20 pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a ansmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum ope specification of 0.064" for good bearing life. Does the dia shown below meet the requirement? if not determine a suitable shaft Sameter. 1.25 in d

gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force 4 applied at the 20 pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a ansmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum ope specification of 0.064" for good bearing life. Does the dia shown below meet the requirement? if not determine a suitable shaft Sameter. 1.25 in d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

Q: Specify the bearings required,

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

Q: A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the…

A: pitch diaDG=100mm=0.1mDP=80mm=0.08mϕ=14.5°σOP=55MPaσOG=55MPaP=2.75kWεP=εG=84kN/mm2

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth Pinion rotates at N1=1200 rpm Torque is…

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-tooth…

Q: 13-50 The figure shows a 10 diametral pitch 18-tooth 20° straight bevel pinion driving a 30-tooth…

A: Given,The diametral pitch,= 10The number of tooth on the bevel pinion, z = 18 toothThe pressure…

Q: The figure shows a 10 diametral pitch 18-tooth 20° straight bevel pinion driving a 38-tooth gear.…

A: The diametral pitch, Pd = 10The number of tooth on bevel pinion, z = 18 toothThe pressure angle = 20…

Q: In the double-reduction gear train shown (dimensions are in inches), shaft a is driven by a motor…

A: Step 1: Step 2: Step 3:

Q: below. Determine: (1) the torque in shaft c-d to the nearest in-lb and (2) the angle of twist at…

A: To determine the torque in the shaft and the angle of twist at a pointgivenradius of gear b=radius…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force
FA applied at the 20 pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a
transmitted force Fg at the pressure angle shown. For the steel countershaft shown below, assume the bearings have a maximum
slope specification of 0.064" for good bearing life. Does the dia shown below meet the requirement? if not determine a suitable shaft
diameter.
1.25-in da
Gear A
F₁-300-
Gear B
Sindia
The minimum shaft diameter is
in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables-

VIEW

Step 2: Determine the value of torque.

VIEW

Step 3: Determine the value of shaft diameter.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

show all solutions and solve both since relate.
Oh no! The bearing at the wall on the left has been damaged. It is now acting like another gear that can resist a moment(TW). You estimate the shaft has had torsional loading as follows: TA= 200 Nm TB= 530 Nm TC= 120 Nm TD= 150 Nm TW =? See the diagram for the direction of the torques on the shaft. The shaft diameter is 60 mm. The shaft looks ok but you are checking to see if it has exceeded the allowed shear stress for the shaft. Tw .600 mm 600 mm 600 mm A) Which segment has the maximum Torsion? B) What is the maximum shear stress due to torsion? C) Assume Tallow = 60 MPa did the shaft exceed the allowed shear?
Q8/ An epicyclic reduction gear shown in figure, has a shaft A fixed to arm. The arm has a pin fixed to its outer end and two gears C and E which are rigidly fixed (C-E compound gear) revolve on this pin. Gear C meshes with annular gear D and gear E with pinion F. G is the driver gear and D is kept stationary. The number of the teeth is as follows: Tp = 80, Tc =10, TE = 24 and Tp = 10. The gear G runs at 200 rpm, find the speed of shaft A. (Area ge D
please help solve
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
The gears shown in the figure form an ideal transmission mechanism. Shaft a applies 8.7 Nm of torque to the pinion (gear 2), which rotates clockwise at 2,312 revolutions per minute. All of the gears have a 20 degree pressure angle. Gears 2 and 3 have a module of 2.5 mm, while gears 4 and 5 have a module of 4 mm. What is the speed of shaft c? Express your answer in units of revolutions per minute. McGraw-Hill Companies, Inc for y 12T NO # + C 3 36T- to 스 3/2 X 18T 30T 5
Q1/ In a planetary gear train shown in the Figure. Determine the angular velocity of gear A. Int Take: TA= 22, Ts= 30, TB= 25, TD= 50, T₁ (Ext.) = 220, TE (Int.) = 200, Ns= +30 rpm, and Narm= -90 rpm. Ext. Arm S D 20
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
Solve correctly please.
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
PLEASE ANSWER PART 4 and 5 Part 1 Calculate the polar moments of inertia in segments (1) and (2). Answer: J₁ = 13.84 in.⁴ J₂= 1.535 in. ⁴ Part 2 Calculate the internal torques T1 and T2 in shaft segments (1) and (2), respectively. On paper, prepare an internal torque diagram for the compound shaft that shows these internal torques. Use the sign convention presented in Section 6-6. Answer: T₁ = 800 Ib-ft, T₂= -800 Ib-ft. Part 3 Calculate the maximum shear stress in each shaft segment. On paper, prepare a diagram that shows the maximum shear stress in segments (1) and (2) of the shaft. Use the sign convention presented in Section 6-6. Answer: τ₁ = 1560.69 psi, τ₂ = -7817.59 psi Part 4 (PLEASE ANSWER) Determine the rotation angle of B with respect to the support at A. Please Answer: φB= rad. Part 5 (PLEASE ANSWER) Determine the rotation angle of C with respect to the support at A. Please Answer: φC= rad.