1-69E The pressure in a natural gas pipeline is measured by the manometer shown in Fig. P1-69E with one of the arms open to theatmosphere where the local atmospheric pressure is 14.2 psia. Determine the absolute pressure in the pipeline.NaturalGas10 in6 inFIGURE P1-69EMercurySG= 13.6Air2 in+25 inWater

Answered: 1-69E The pressure in a natural gas…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q マつ 13,600 kg/m) is con- 1-67 A mercury manometer (p nected to an air duct to measure the pressure inside. The difference in the manometer levels is 15 mm, and the atmospheric pressure is 100 kPa. (a) Judging from Fig. P1-67, determine if the pressure in the duct is above or below the atmospheric pressure. (b) Determine the absolute pressure in the duct. Air h = 15 mm P = ? FIGURE P1-67 hp
A closed vessel contains air at a pressure of 10 Kpag and temperature of 20 0C. Find the final gauge pressure if the air is heated at constant volume to 40 0C. Take the atmospheric pressure as 759 mm Hg. Show complete solution and the final answer should be rounded to 4 decimal places
i need the answer quickly
The pressure difference between two points as measured with a manometer is given as p2-p1=pgh . The following figure shows a single u-tube manometer measuring pressure difference between point A and B. By determining the pressure at point "a" through the left leg and then through the right leg,show the difference in pressure between point A and B is approximately given by PA-PB=g(h2-h1) (pH20)
Question 2 A gasoline line is connected to a pressure gage through a double U-manometer, as shown in fig below. If the pressure gage is 370 kPa, determine the gage pressure of the gasoline. Oil SG 0.79 Pse=370 kPa Enge Gasoline SG=0.70 45 cm 50 cm Pipe Air 22 cm 10 cm Mercury SG= 13.6 Water FIGURE P1-112 Add a caption... > Gideon Yalley
Need quick handwritten solution. The gauge pressure in the air container in Fig. P1-83 is 80kPa . Calculate the differential height h of the column of mercury.
In the figure, fluid 2 is carbon tetrachloride(1.589) and fluid 1 is benzene (SG = 0.877). If the atmospheric pressure is 101.5 kPa, determine the absolute pressure at point A. Patm fluid 1 35cm 12 cm fluid 2 Fig. 2-26 Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa abs
1-80 Consider the manometer in Fig. P1-78. If the specific weight of fluid B is 20 kN/m³. what is the absolute pressure. in kPa, indicated by the manometer when the local atmo- spheric pressure is 720 mmHg?
A rigid, hermetically sealed container contains two fluids: water (103 kg / m3 ) and air. A pressure gauge, attached to the top of the tank, indicates a pressure 40 kPa vacuum gauge. If the atmospheric pressure of the place is 105 Pa and the water inside the container has a height of 30 cm, determine the absolute pressure at the bottom of the tank. Consider that the gravitational acceleration of the place is 9.8 m / s2 . a) 60 kPa b) 62.94 kPa c) 142.94 kPa d) 57.06 kPa
1-53 The water in a tank is pressurized by air, and the pres- sure is measured by a multifluid manometer as shown in Fig. PI-53. Determine the gage pressure of air in the tank if h = 0.2 m, h, = 0.3 m, and h, = 0.46 m. Take the densities of water, oil, and mercury to be 1000 kg/m'. 850 kg/m, and 13.600 kg/m, respectively. Oil Aic Mercuty FIGURE P1-53 Scanned with CamScanner at a aeptn oI Y m. at uic UL 1-56 The absolute pressure in water at a depth of 5 m is read to be 145 kPa. Determine (a) the local atmospheric pres- sure, and (b) the absolute pressure at a depth of 5 m in a liq- uid whose specifc gravity is 0.85 at the same location. Neglectin eration, average 1-64 Scanned with CamScanner D FIGURE P1-58E 1-59 The piston diameters in Fig. Pl-58E are D, = 10 cm and D, = 4 cm. When the pressure in chamber 2 is 2000 kPa and the pressure in chamber 3 is 700 kPa, what is the pres-
The surface tension of a liquid is being measured with a ring as shown in the figure. Thering has an outside diameter of 10 cm and an inside diameter of 9.5 cm. The mass of thering is 10 g. The forcerequired to pull the ring from the liquid is the weight corresponding to a mass of 16 g.What is the surface tension of the liquid (in N/m)?
Im unsure of how to answer this question in preparation for my exam

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS