1.12 You've experienced convection cooling if you've everextended your hand out the window of a moving vehi-cle or into a flowing water stream. With the surface ofyour hand at a temperature of 30°C, determine the con-vection heat flux for (a) a vehicle speed of 40 km/h inair at -8°C with a convection coefficient of 40 W/m² Kand (b) a velocity of 0.2 m/s in a water stream at 10°Cwith a convection coefficient of 900 W/m²K. Whichcondition would feel colder? Contrast these results witha heat flux of approximately 30 W/m² under normalroom conditions.

Approach to solving the question: Detailed explanation:The question involves calculating the…

Answered: 1.12 You've experienced convection…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.57P

See similar textbooks

Similar questions

The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
Using Table 1.4 as a guide, prepare a similar table showing the orders of magnitude of the thermal resistances of a unit area for convection between a surface and various fluids.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Determine the rate of heat loss from the wall of a building resulting from a 16 km/h wind blowing parallel to its surface. The wall is 24 m long and 6 m high, its surface temperature is 27C, and the temperature of the ambient air is 4C.
1.19 A cryogenic fluid is stored in a 0.3-m-diameter spherical container is still air. If the convection heat transfer coefficient between the outer surface of the container and the air is 6.8 , the temperature of the air is 27°C, and the temperature of the surface of the sphere is –183°C, determine the rate of heat transfer by convection.
1.21 In an experimental set up in a laboratory, a long cylinder with a 5-cm diameter, and an electrical resistance heater inside its entire length is cooled with water flowing crosswise over the cylinder at and a velocity of 0.8 m/s. For these flow conditions, 20 kW/m of power is required to maintain a uniform temperature of at the surface of the cylinder. When water is not available, air at is used with a velocity of 10 m/s to maintain the same surface temperature. However, in this case, the cylinder surface heat dissipation rate is reduced to 400 W/m. Calculate the convection heat transfer coefficients for both water and air, and comment on the reason for the differences in the values.
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
1.79 Consider the cooling of (a) a personal computer with a separate CPU and (b) a laptop computer. The reliable functioning of these machines depends on their effective cooling. Identify and briefly explain all modes of heat transfer involved in the cooling process.
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning