1.The cylinder B has a weight of 15-lbsand is attached to the 20-lbs block A using thecord and pulley system shown. Determine allthe loads that are applied to the cylinder B,when the block A is released and starts tomove. The coefficients of static and kineticfriction on all surfaces are 0.3 and 0.2respectively.B0.3 ftA60°

May this answer helpful to you.

Answered: 1. The cylinder B has a weight of…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

Q2/ As shown in fig. the beam AB is subjected to a uniform load of 200N/m and is supported at B. Find the reaction at B. If the coefficients of static friction at B are μB = 0.2, determine the force P needed to pull the post out from under the beam. Neglect the weight of the members and the thickness of the beam. 4 m 200 N/m B 0.75 m I 10.25 m
Q5 Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when 9=40° and P-400 N. 800 N H=0.20 Hk=0.15 23°
Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when 0 = 30° and P= 45 lb. Given: μs = 0.30 and k = 0.20. 250 lb The block is not in equilibrium and moves down. True The magnitude and direction of friction force is 86.03 lb 7
1. The crate is being pulled by the man as shown. Given that thecoefficient of the horizontal surface and the 750-lb crate is 0.35,find the pulling force on the rope the man should apply to putthe crate in impending motionF =2. Determine the weight of block B for the 250N block A not to slidedown in the inclined plane. Given that the coefficient of staticfriction in the 45° inclined plane is 0.25 and in the 30° inclinedplane is 0.3. (Assume frictionless pulley)WB =
The 150 lb block rests on an inclined surfacevand is attached to a frictionless pulley C. The coefficient of static friction between the block and the incline is 0.25. The dope passes over a drum D, where the coefficient of static friction between the rope and the drum is 0.2, as shown. Find the minimum and maximum values for the weight of block B, Wb, for which no motion will occur. Neglect tipping.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is = 0. - 4m -
B: A roll of paper has a uniform weight of 2kN and is suspended from the wire hanger so that it rests against the wall. If the hanger has a negligible weight and the bearing at 0 can be considered frictionless, determine the force P needed to start turning the roll if 6 = 30°. The coefficient of static friction between the wall and the paper is µ, = 0.3. 12 cm
For the given set up, the two cylinders on the left and right are movable horizontally, while the cylinder in the middle is fixed. Determine the distance a so that the system is in equilibrium and the tension T2 is equal to 2.5 N and T₁ is equal to 2.0 N. The radius of the three cylinders is equal to 20 mm, while the coefficient of friction between the cylinder and the rope (u) is 0.1529. T₁ T₂ a B
1. If the spring is compressed a distance 6 and the coefficient of static friction between the tapered stub S and the slider A is sA, determine the horizontal force P needed to move the slider forward.The stub is free to move without friction within the fixed collar C. The coefficient of static friction between A and surface B is µAB. Neglect the weights of the slider and stub. Given: 8 = 60 mm HsA = 0.5 HAB = = 0.4 N k = 300 e = 30 deg B
Also determine the magnitude of the force exerted by the hammer head on the block at A. Express your answer in units of lb.
The two 200N blocks are pushed apart by the 15⁰ wedge of negligible weight. The angle of static friction is 12⁰ at all contacts surfaces. Determine the force P required to start the blocks moving.
Determine whether the block shown below is in equilibrium, and find the magnitude and direction of the friction force. Draw the Free-body diagram and show all calculations. Given: coefficient of static friction u, = 0.30 and coefficient of kinetic friction u = 0.25. H=0.30 600N H=0.25 700N 30

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L