9) Counterboring is a process ofa) Cutting threads in a Workpieceb) Making precise hole in a Workpiecec) Making shape for a Socket Flathead cap screw in aworkpieced) Making shape for a Socket head cap screw in aWorkpiece10) Countersinking is a process ofa) Cutting threads in a Workpieceb) Making precise hole in a Workpiecec) Making shape for a Socket Flathead cap screw in aWorkpieced) Making shape for a Socket head cap screw in aWorkpiece11) What size drill is used to Ream 1/4 inch hole?a) 0.250b) 0.235c) 0.248d) 0.20012) What size drill is used for ½ -13 tapped hole?a) 0.423b) 0.485c) 0.498d) 0.312

9) Counterboring:Correct answer: d) Creating a recess for a Socket head cap screw in a…

Answered: 9) Counterboring is a process of a)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7-9.
42) What are the names given to the three Taps used for Tapping Holes? a) Taper, Plug,Bottoming b) Taper, Fine, Course c) Fine,Course, Bottoming d) Top,Bottoming, Side 43) What does 16 represent for the Notation of 3/8-16UNC- 2A. a) Outside Diameter of a screw b) 16 Threads per Inch c) Fine Thread of the Screw d) Thread Tolerance 44) What does 3/8 represent for the Notation of 3/8-16 UNC- 2A a) Outside diameter of the Screw b) 16 Threads per Inch c) Fine Thread of the screw d) Thread Tolerance 45) Cutting Speed is ? a) The Peripheral distance travelled by The cutter b) The RPM of the Chuck c) The speed of the metal chips being cut d) The Feed Rate
19-21 Answer it correctly and this is Asap I will rate helpful if fast and perfect
Note: I need both answer with clear explanation. Don't copy from other expert answer Urgenttttttt please
10-12 Answer it correctly and this is Asap I will rate helpful if fast and perfect
Tooth breakage on gear is usually a A) A crack B) None of These C) A contact Stress D) A Tensile fatigue
Which one of the options isn't classified as a chip form type? a)Non-segmental chip b)Sheared chip c)Discontinuous chip d)Continuous chip
17) The Feed Rate on a Conventional lathe is measured in a) Feet per minute b) Inches per Revolution c) Inches per minute d) Inches per tooth 18) From a feed and Speed chart we find that a single point lathe tool is given a cutting speed of 100 FPM and a feed per revolution 0.007.If the diameter of the Workpiece is 1.25 inches What is the correct RPM and Feed rate used on the Lathe? a) 320 RPM and 0.007 IPR b) 100 RPM and 7 IPM c) 3200RPM and 0.007 IPR d) 125 RPM and 0.007 IPR 19) To Fix a small bump left on the Face of a workpiece in a lathe a) Use a file b) Ignore it c) Adjust the tool on centre again 20) The best tool to use to Chamfer a hole is a a) Chamfer file b) Counterbore c) Countersink d) Reamer 01
Gear finishing operation is called: A) Burnishing B) Hobbing C) Shaping D) Milling
21) A Tap is driven with a) An adjustable Wrench b) A Combination Wrench c) A Tap Wrench d) Pliers 22) The alignment of a Tap could be checked with a a) Plumb Bob b) Square c) Level d) Dividers 23) The size of a Tap Drill is important because it a) Determines the size of a Thread b) Regulates the percentage of Thread c) Forms the Major Diameter d) Determines the depth of the hole 24) If the drilling speed is too high for the diameter of the drill and the Material being drilled, the result is a) A Rough hole b) Chips jammed in the Flutes c) The Margins or outer corners are broken down d) More feed is required to get the drill to cut and the drill can break
Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a 95.8 mm cylinder to 30.04 mm using 7 roughing passes and 3 finishing passes. The finishing operations use a depth of cut of 1.51 mm. The roughing operations are performed with a feed rate of 9.61 mm/s and the finishing operation is performed with a feed rate of 11.31 mm/s. a) What is the depth of cut for a roughing pass? b) What is the rate of material removal (mm^3/s) for the third roughing pass? c) What is the rate of material removal (mm^3/s) for the final finishing pass? d) What is the average rate of material removal (mm^3/s) for the roughing operations?
An orthogonal cutting operation is being carried out in which to=0.2 mm, V=2m/s, a=7.5o, and the width of cut=5 mm. It is observed that tc=0.25mm, Fc=400N, and Ft=300N. Calculate the percentage of the total energy that is dissipated in friction at the tool-chip interface. A) 22% B) 50% C) 70% D)None of the above

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS