For the planetary gear train shown:N₂ = 20t, N₁ = 40t, N₁ = 18t, N₁ = 36t, N₁ = 154t.3 is the arm (carrier) connecting planet gears N, and Ns.Inputs are the ring gear with an angular velocity of 100 rpm cow and the arm with an angularvelocity of 50 rpm cw,1547407367Gears 5 and 6 are on the sameshaft.207Gears 5 and 4 are meshed. Gears 4and 2 are meshed.1873 denotes the carrier (arm).a. Determine the angular velocity of planet gear 5. What are the gear sets and gear ratio for thisquestion?b. Determine the angular velocity of the sun gear. What are the gear sets and gear ratio for thisquestion?

Answered: Image /qna-images/answer/a6074c35-92a8-4c7a-83a2-cb512f8be142.jpg

Answered: For the planetary gear train shown: N₂…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the planetary gear train shown: N₂ = 20t, N4 = 40t, N5 = 18t, №6 = 36t, N7 = 154t. 3 is the arm (carrier) connecting planet gears N4 and N5. Inputs are the ring gear with an angular velocity of 100 rpm ccw and the arm with an angular velocity of 50 rpm cw, 154T 40T 36T W7 20T 3 18T 6 Gears 5 and 6 are on the same shaft. Gears 5 and 4 are meshed. Gears 4 and 2 are meshed. 3 denotes the carrier (arm). a. Determine the angular velocity of planet gear 5. What are the gear sets and gear ratio for this question? b. Determine the angular velocity of the sun gear. What are the gear sets and gear ratio for this question?
I need the answer as soon as possible
Answer d and e
A commercial enclosed spur gearset has 22 teeth on the pinion and 60 teeth on the gear. The pressure angle is 20° and the overload factor Ko =1. The diametral pitch is 8 teeth/in and the face width is 5 in. The pinion speed is 1000 rev/min and its cycle life is to be 10° revolutions at a reliability R =0.50. The quality number is 5 and the tooth are crowned. The material is a through-hardened steel, grade 2, with Brinell hardnesses of 250 core and case of both gears. For a conservative design and bending stress design factor of 2, rate the pinion (power) for these conditions using the AGMA method.
1. For the following simple gear train determine the angular velocity and torque of gear 6. 2 A M₂ @₁ = 1800 rpm T₂ = 1200lbf-in N₂ = 17 teeth N₁ = 28 teeth N₁ = 12 teeth N N₁ = 38 teeth N6 = 24 teeth N6 FIGURE 9-28 A simple gear train
The following data refer to two meshing involute gears of 20° pressure angle: Number of teeth on pinion 20, speed ratio = 2, speed of pinion = 250 rpm, module = 12 mm The addendum of each wheel is such that the path of approach and path of recess on each side are half of the maximum possible length. 1) Illustrate the value of addendum for both wheels, 2) Identify the length of arc of contact, and, 3) Formulate the free body diagrams for wheels in connection.
3. For the following planetry gear train determine the following -Internal gear connected to drive shaft, 427 Sun gear: -Planet pinions, 127 Planet carrier connected to transmission Figure not to scale. N2 = 24 teeth, Input to Sun gear: w₂ = 100 rpm ccw, T₂ = 1000 lbf-in Input to Ring gear: ws = 240 rpm cw a. Determine the angular velocity of the carrier. (units and direction). b. Determine the torque on the arm.
Please answer the question in details
Two 20º full-depth steel gears are heat treated to BHN=350. AGMA Quality No.8 Pinionturns 860 rpm. N1=24c; N2=96; Pd=4, and b=2in. Find the horsepower the gears aretransmitting. Ans: hp=77.2
For the simple gear train shown, calculate the output angular velocity. 130 rpm Wout Output Input N = 20 N = 45 %3D Teeth N = 95
What is the size factor, Ks, for the pinion? This should be an exact value.
Hello good Afternoon Sir, Permission, i have a question in my homework. The following bellow is question. Please advice. Thank you Regards,Irfan In planning the combined gears of the Ferguson planetary paradox as shown in the figure below.Sun gear hand input with angular speed (w2) = 0 rpm and hand input with angular speed (w.arm) = 400 rpm counterclockwise (ccw)Where is the number of teeth:Sun gear N2 = 100 (external gear)Sun gear N3 = 99 (external gear)Sun gear N4 = 101 (external gear)Planet gear N5 = 20 (external gear)Calculate the angular velocity, for each gear using the tabulation method. The data is in the image below

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS