A commercial enclosed spur gearset has 22 teeth on the pinion and 60 teeth on the gear. The pressure angle is 20 and the overload factor Ko =1. The diametral pitch is 8 teeth/in and the face width is 5 in. The pinion speed is 1000 rev/min and its cycle life is to be 10° revolutions at a reliability R =0.50. The quality number is 5 and the tooth are crowned. The material is a through-hardened steel, grade 2, with Brinell hardnesses of 250 core and case of both gears. For a conservative design and bending stress design factor of 2, rate the pinion (power) for these conditions using the AGMA method.

A commercial enclosed spur gearset has 22 teeth on the pinion and 60 teeth on the gear. The pressure angle is 20 and the overload factor Ko =1. The diametral pitch is 8 teeth/in and the face width is 5 in. The pinion speed is 1000 rev/min and its cycle life is to be 10° revolutions at a reliability R =0.50. The quality number is 5 and the tooth are crowned. The material is a through-hardened steel, grade 2, with Brinell hardnesses of 250 core and case of both gears. For a conservative design and bending stress design factor of 2, rate the pinion (power) for these conditions using the AGMA method.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
14-23 A spur gearset has 17 teeth on the pinion and 51 teeth on the gear. The pressure angle is 20° and the overload factor K, = 1. The diametral pitch is 6 teeth/in and the face width is 2 in. The pinion speed is 1120 rev/min and its cycle life is to be 10" revolu- tions at a reliability R = 0.99. The quality number is 5. The material is a through- hardened steel, grade 1, with Brinell hardnesses of 232 core and case of both gears. For a design factor of 2, rate the gearset for these conditions using the AGMA method.
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
Hi, Please help me with this problem, Thank you
A steel spur pinion has 16 teeth cut on the 20° full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 5 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the gears is 5 kN. If the contact fatigue strength of the steel can be estimated from the AGMA formula of Sc= 2.22 HB + 200 MPa, estimate the factor of safety of the drive based on a surface fatigue failure. The factor of safety of the drive is
Compute the values for all the geometrical features for a pair of straight bevel gears having a diametral pitch of 8, a 20° pressure angle, 16 teeth in the pinion, and 48 teeth in the gear. Specify a suitable face width. The shafts are at 90°. tad wo m that ratates at1750 com
None
A spur gear reducer is to transmit 4 kW at 1500 rpm of the pinion of cast steel ( So=138 MPa). The gear is made from phosphor bronze (So=83 MPa). The velocity ratio is 3.5 to 1.0. Assume a pressure angle of 20°. Design the gears for strength only.
Hello, Please help me with this problem. Thank you