Please use the Chilton-Colburn analogy when solving. A thin, flat plate that is 0.2 m × 0.2 m on a side is oriented parallel to an atmospheric airstream havinga velocity of 40 m/s. The air is at a temperature of 20 °C, while the plat is maintained at Ts = 120 °C.The airflows over the top and bottom surfaces of the plate, and measurement of the drag force revealsa value of 0.075 N. What is the rate of heat transfer from both sides of the plate to the air? Properties:Air (70 °C): p = 1.018 kg/m³, cp = 1009 J/Kg K, Pr = 0.70, v = 20.22×10-6 m²/s.4-40m/sToo =20°Cp=1atm= 0.2m0.2m-T=120°C-=0.075 N

Answered: Image /qna-images/answer/4994761e-4016-43d1-9ad1-3318fe4cbd65.jpg

Answered: A thin, flat plate that is 0.2 m × 0.2…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.49P

See similar textbooks

Similar questions

Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Atmospheric air is in parallel flow (u∞ = 10 m/s, T = 15°C) over a flat heater surface that is to be maintained at a temperature of 90°C. The heater surface area is 0.25 m², and the airflow is known to induce a drag force of 0.17 N on the heater. What is the electrical power, in kW, needed to maintain the prescribed surface temperature? Use the modified Reynolds or Chilton-Colburn analogy. Evaluate properties for the air at 325 K. q= i kW
1-The wind blows with velocity 0.4 m/s parallel to the both sides of a flat plate with rectangular area 10m×10 m. The plate temperature is T0=60◦C, and the temperature of the air free stream is 20◦C. Assume laminar flow and calculate: (a) maximum boundary layer thickness, (b) the total force experienced by the plate, (c) estimate the total heat transfer rate by laminar forced convection (d) Make a qualitative sketch of how the local heat flux qx and τx varies along the length L.
Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40⁰C and. The plate temperature is 100⁰ C while the air speed is 5 m/s.Find the thickness of the boundary layer at a distance of x = 20 cm.
Air at standard pressure flows across a flat plate at 3m/s. The temperature surface is 50oC and the surrounding temperature is 20o Consider a point 1m away from the leading edge of the plate. See Table A-15 in Appendix 1 for properties of air. Determine the Reynold’s number and Prandtl number for this flow at the location described above. Determine the local flow boundary layer thickness. Determine the local thermal boundary layer thickness for this flow.
Use scale analysis to find an expression for 8/x and Nu for flow over a flat plate with a thin thermal boundary Layer. Find the expression 8/x = 4.92 Re** Consider the following NACA airfoils: 2412, 23012, 23021 a. For each of these airfoils, find the L/D ratio for angle of attack of 0, 4, 8 and 12 b. For each airfoil find the angle of maximum L/D and find the stall angle c. Find which airfoil will provide the maximum lift for any given geometry and flow conditions
A flat plate is experiencing a parallel air flow over the top surface with an average friction coefficient (CF) of 1.842×104. All properties of air are listed in the figure. What is the average convection coefficient (h) on the top surface? Please show the complete analysis procedure. u = 40 m/s Pr = 0.7 Ts > Too p=1.018 kg/m³ C = 1.842x10-4 Cp = 1009 J/kgK Modified Reynolds Analogy f Cƒ = 2St Pr²/3 (0.6 < Pr < 60) (6.70)
Air at 305 K flows at 4 m/s over a flat plate at 350 K. The air properties are as follows: density =1.1 kg/m3, viscosity =18.1×10−6 Pa.s, specific heat capacity =1005 J/kgK, and thermal conductivity =0.024 W/mK. The velocity and temperature profiles are assumed to be linear, giving the local Nusselt number to be Nux = 0.289 Rex1/ 2Pr1/3. The flow will become turbulent at a Reynolds number of 5×105. Assume the width of the plate perpendicular to the air flow is 1 m. At what distance from the leading edge does the flow become turbulent? ________m What is the heat transfer at the point of transition? ___________W What is the total heat transfer along the length of the plate where the flow is laminar? __________W
Air at 20-C and 1 atm flows over a flat plate at 35 m/s. The plate is 75 cm long and is maintained at 60-C. AJASsuming unit depth in the z direction, calculate the heat transfer from the plate. Calculate the turbulent-boundary-layer thickness at the end of the plate assuming that it develops B) from the leading edge of the plate and C) from the transition point at Recrit =5x105.
Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40⁰C and. The plate temperature is 100⁰ C while the air speed is 5 m/s.Find the thickness of the boundary layer at a distance of x = 20 cm, for the same data in problem "number 1 In the picture below"
What’s the correct answer for this please?
Air is flowing at a speed of 30 m/sec over a flat plate. The air temperature is 20o C and its pressure is 1 atm. The plate is kept at a constant temperature of 65o C. What is the heat transfer rate per unit length between 7.5 cm to 30 cm, from the edge of the plate?

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning