(ANS: -388 psi,Determine the stress components acting on the inclined plane AB. a) solve using the method of equilibriumfrom section 9.1, and b) Solve using the stress-transformation equations developed in Sec. 9.2.455 psi)400 psi60°650 psiB

Answered: (ANS: -388 psi, Determine the stress…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
Determine the stress components acting on the inclined plane AB in if: normal stressy = 61MPa shear stressxy = -25 MPa solve the problem using the method of equilibrium. Find normal stress x' =? find shear stress x'y' =? I have a question regarding the answer you provided. The shear stress is -25MPa. You used a positive 25MPa in the solution. Why is that?
5- (h.w.): In a certain material under load a plane AB carries a tensile direct stress of 30 MN/m? and a shear stress of 20 MN/m2 while another plane BC carries a tensile direct stress of 20 MN/m2 and a shear stress. If the planes are inclined to one another at 30° and plane AC at right angles to plane AB carries a direct stress unknown in magnitude and nature, find :- (a) The value or the shear stress on BC. (b) The magnitude and nature of the direct stress on AC (c) The principal stresses 20 9. 300 20 nd Shells B 30 20
The W-kg man stands in the position shown. If the center of gravity of the man is at Gand assuming that the contact point at C is smooth.a) Find the reactions at B and C. b) Determine the state of stress at point A on the cross section of the plank at sectiona–a (Cubic stress element in 2D).
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).
7
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
The solid rod shown in the figure has a radius of 0.75 inches. Determine the state of stress at point A with respect to the x, y, and z system of axes if: Part A.) the rod is loaded with a force of 500 lb as shown in the top figure. Part B.) the rod is loaded with a force of 800 lb as shown in the bottom figure.
3. As shown, a vertical 200 lb force is applied to the gear and shaft assembly at point D. Shaft ABC is solid and has a 0.5 in. radius. (you may use a coordinate system of your choice, as long it's correct.) y 2.5 in. 10 in. D H B Z X 200 lb a) Determine the state stress (all stresses with their indices) at point H on top of the shaft. b) Determine the principal stresses and max shear stress at point H.
determine the effective stress at point D
At point O of a part subjected to plane stress made of steel material (E = 210 GPa and v= 0.3) the tensile components are given below. 240 50 0= , o, Tyz 50 - 30 %3D MPa 0 0 a) The principal stress components (01, 02 and o3) and their angles with respect to the x-y-z axes of the planes where they are formed calculate. b) Calculate the maximum shear stress (tmax). c) Drawthe 2-D and 3-D Mohr circles for the stress components. d) If the yield strength of the steel material is 250 MPa, according to the Tresca ww damage criterion, it will not flow at the O point of the part. Indicate whether it is safe or not.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

(ANS: -388 psi, Determine the stress components acting on the inclined plane AB. a) solve using the method of equilibrium from section 9.1, and b) Solve using the stress-transformation equations developed in Sec. 9.2. 455 psi) 400 psi 60° 650 psi B