Consider a single crystal of a metal oriented such that a tensile stress is applied along the [001]direction. The single crystal has a length of 30 mm along the [001] direction and a cross-sectional diameter of 3 mm. If slip occurs on the (111) plane and in the [1601] direction whenthe applied tensile load reaches 500 N, compute the critical resolved shear stress. Note thatthe angle between the [001] and the plane normal of (111) is 54.7°, and the angle betweenthe [001] and [1601] directions is 45°. (pls provide full calculations)

Consider a single crystal of a metal oriented such that a tensile stress is applied along the [001]direction. The single crystal has a length of 30 mm along the [001] direction and a cross-sectional diameter of 3 mm. If slip occurs on the (111) plane and in the [1601] direction whenthe applied tensile load reaches 500 N, compute the critical resolved shear stress. Note thatthe angle between the [001] and the plane normal of (111) is 54.7°, and the angle betweenthe [001] and [1601] directions is 45°. (pls provide full calculations)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.7.5P: Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight...

See similar textbooks

Similar questions

Only part e, please.
If ß-Sn, a tetragonal crystal (point group 4/mmm, a = 0.583 nm, and c = 0.318 nm) is subject to a tensile stress of 63 MPa along [100] and to a shear stress of 18 MPa on the (100) plane in the [010] direction. Determine: a) the tensile stress normal to (110), and b) the shear stress on the (110) plane in the [1-10] direction.
Problem 4: The state of stress at a particular point in a structure is given below. 10 20 0 ¹-[20 = 20 -10√2 MPa 0 -10√2 10/27/1 [o] (a) Write the characteristic equation (cubic equation) that would be used to determine the principal stresses. (b) Without solving the characteristic equation, verify that one of the principal stresses is Op = 30 MPa. Find its corresponding principal direction (i.e., find its direction cosines). (c) Determine the other principal stresses and their corresponding principal directions. (d) Determine the maximum shear stress.
A copper rod [E= 110 GPa] originally 599 mm long is pulled in tension with a normal stress of 278 MPa. If the deformation is entirely elastic, what is the resulting elongation (in mm)? Note: Do not include units in your answer Answer:
4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test it for rupture what load cell you should use (25ON or 5kN) what problems may occur if you select an incorrect load cell. 5. The figure below is a J-shaped (or concave upward) stress-strain curve. What does a J-shaped stress stain curve indicate about a material's response to stress and tendency to yield? Name two materials that have J-shaped stress strain curves.
Q/Figure i shows the stress and strain curve of a ... metal sample of standard length (250 mm) and diameter (10.3 mm) that has been tested for tensile strength until fracture .. Use the figure to answer the following .. I- Is the material coated (Ductile) or brittle? 2-Why does the curve change downward when the stress is reached? 3-What is the resistance to succumbing to this sample? 4-Calculate the highest tensile strength the sample can withstand? 10 Maximum stress 8. 6 4 1 Fig 1 Strain Stress (Mpa)
Please calculate each material individually Steel 4340 Maraging Steel A1 7075
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
Please solve in detail. Don't use chatgpt,The Free body diagram must be drawn.
The diagram below shows a microscopic metal rod with a single crystal structure whose orientation is indicated by the inset. A force of F = 25.8 N is applied to the rod. The cross-sectional area is 1.9 mm². Calculate the shear stress along the close-packed direction. O a. 5.10 MPa O b. 6.10 MPa c. 4.66 MPa O d. 5.54 MPa Oe. 4.05 MPa
Please solve all part's correctly
Learning Goal: A material is homogenous and isotropic when it has a modulus of elasticity that does not vary with direction and it has uniform properties throughout. When a point in a material is subjected to only normal stresses in three dimensions, but they are not necessarily equal, the state is called triaxial stress. When the response of the material is linear elastic, the strains along the three axes can be calculated using a generalized form of Hooke's law. Each strain depends on all three stresses because of the Poisson effect. €1 Figure 1 [0₂ - V (O₂ +0₂)] a 1 of 1 A cube is subjected to stresses with magnitudes a = 16 MPa, b = 26 MPa, and c = 5 MPa (Figure 1). What is the strain in the y-direction? Let E = 200 GPa and v= 0.26. Express your answer to three significant figures. ► View Available Hint(s) Submit VE ΑΣΦ Part B - Change in volume f change in volume = vec The cube from Part A originally has side length 3.2 cm . What is the change in volume of the cube under the given…