The beam is supported by a pin at B and a roller at C and is subjected to the loading shown with w =120 lb/ft, and F 335 lb. a.) If M = 3,580 ft-lb, determine the support reactions at B and C. Report your answers in both Cartesian components. b.) Determine the largest magnitude of the applied couple M for which the beam is still properly supported in equilibrium with the pin and roller as shown. 2013 Michael Swanbom cc 10 BY NC SA M лу W F x Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 2.4 ft b 6 ft с 2.6 ft a.) The reaction at B is B 840 The reaction at C is C 214 = 0 ☑ it i+ ✓ lb. = 0 i+ × ĵ lb. b.) The largest couple that can be applied is M = 5041 x ft-lb.

The beam is supported by a pin at B and a roller at C and is subjected to the loading shown with w =120 lb/ft, and F 335 lb. a.) If M = 3,580 ft-lb, determine the support reactions at B and C. Report your answers in both Cartesian components. b.) Determine the largest magnitude of the applied couple M for which the beam is still properly supported in equilibrium with the pin and roller as shown. 2013 Michael Swanbom cc 10 BY NC SA M лу W F x Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 2.4 ft b 6 ft с 2.6 ft a.) The reaction at B is B 840 The reaction at C is C 214 = 0 ☑ it i+ ✓ lb. = 0 i+ × ĵ lb. b.) The largest couple that can be applied is M = 5041 x ft-lb.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

6.) please help
Need help, please round answers to 3 sig figs
Don't provide handwritten solution.
Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 981 N 0.5 m 0.1 m By 0.4 m B 30% 0.3 cos 30°m X 0.3 m G 0.5 m 0.1 m 0.1 m X 100 kg 0.3 m 30% 0.3 m
Determine the vertical component of the pin reaction at C.
The 400-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical. Positive values are to the right, up, and counterclockwise. 43 kN-m 33 4.2 kN A B 2.7 kN - 1.2 m-- 1.7 m 1.7 m Answers:
Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.
Can you help me with this question,Do fast.
please is urgent The 7.8m steel I-beam has a mass of 800kg and is lifted into position by applying a force P on the trolley to which the lower end B is secured. Cable AC is tied center of the beam and is horizontal when B is exactly below C. Determine, in function of x, the force P needed to maintain equilibrium from x=0 to the value of x at which A' lies exactly below C. Find the maximum value of P and the corresponding value of x.
The weightless beam shown below is in static equilibrium and supported by a roller at A and a pin at B. Determine the reaction forces at A and B when d = 3 ft, h = 7 ft, P = 300 Ibf and a = 25°. a B h d
24. The 30-lb homogeneous bar AB supports the 60-lb block. The ends of the bar rest on 30 lb 60 Ib B frictionless inclines. Determine 12 ft 30 the distance x for which the 60 bar will be in equilibrium in the position shown. Answer: 10.5 ft Figure SP-3.18
A) The axially loaded bar is fixed at A and loaded as shown. Draw a free-body diagram and determine the support reaction at A. On paper, draw a free-body diagram of the bar and determine the reaction at A for the bar to be in equilibrium. Assume that the unknown reaction at A acts in the negative x direction. B)Using the answer from Part A, draw free-body diagrams or a load diagram and determine the internal axial forces in segments AB, BC, and CD. C)Using the internal axial forces determined in Part B, calculate the bar's maximum average normal stress. Using your free-body diagrams or load diagram from Part B and the axial stress equation, calculate the bar's maximum average normal stress.