In the vulcanization of tires, the carcass is placed into a jig and steam at 149°C is admitted suddenly to both sides. If the tire thickness is 2.5 cm, the initial temperature is 21°C, the heat transfer coefficient between the tire and the steam is 150 W/(m2 K), and the specific heat of the rubber is 1650 J/(kg K), estimate the time required for the center of the rubber to reach 132°C

In the vulcanization of tires, the carcass is placed into a jig and steam at 149°C is admitted suddenly to both sides. If the tire thickness is 2.5 cm, the initial temperature is 21°C, the heat transfer coefficient between the tire and the steam is 150 W/(m2 K), and the specific heat of the rubber is 1650 J/(kg K), estimate the time required for the center of the rubber to reach 132°C

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.10P: 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the...

See similar textbooks

Similar questions

2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
Find out the diameter of the spherical product being frozen in an air-blast wind tunnel. The initial product temperature is 100C & cold air in the tunnel is at -120C. The product density is 1000 kg/m3 and the convective heat transfer coefficient for the air blast is 50 W/m2K. The thermal conductivity of the product is 1.25 W/mK and the initial freezing temperature is -20C. The latent heat of fusion is 300 kJ/kg. Freezing time is 2.2 hrs
An egg with mean diameter of 40 mm and initially at 20 °C is placed in a boiling water for (4min) and found to be boiled to consumers taste. For how long should a similar egg for same consumer be boiled when taken from a refrigerator at 5 °C. Take the following properties for egg: k = 10 W/m. °C , p= 1200 kJ / kg. °C C = 2 kJ / kg . °C, and the heat transfer coefficient (h = 100 W/m?. °C)
a) A turbine blade 6 cm long and having a cross sectional area 4.65 cm and perimeter 12 cm is made of stainless steel (k=23.3 Wim K). The temperature at the root is 500 C. The blade is exposed to a hot gas at 870 °C. The heat transfer coefficient between the blade surface and gas is 442 W/im K. Determine the temperature distribution and rate of beat flow at the root of the blade, Assume the tip of the blade to be insulated. b) The hot combustion gases of a fumace are separated from the ambient air and its surounding, which are at 20°C, by a brick wall 0.5 m thick. The brick has a themal conductivity of 5 W/mk and a surface emissivity of 0.6. Under steady-state conditions an Page no.1 of 1 outer surface temperature of 120°C is measured Free convection heat transter to the air adjoining the surface is characterized by a convection coefficient of 15 Wim K What is the brick inner surface temperature
Steel balls 12 mm in diameter are annealed by heating to 1100 K and then slowly cooling to 360 K in an air environment for which T. = 325 Kand h = 20 W/m2-K. Assuming the properties of the steel to be k = 40 W/m-K,p = 7800 kg/m, and c = 600 J/kg-K, estimate the time required for the cooling process. The time required for the cooling process isi h.
The physics of the convection heat transfer of thermosses phenomenon and the mathematical model should be discussed.
Heat Transfer with a Liquid Metal. The liquid metal bismuth at a flow rate of 2.00 kg/s enters a tube having an inside diameter of 35 mm at 425°C and is heated to 430°C in the tube. The tube wall is maintained at a temperature of 25°C above the liquid bulk temperature. Calculate the tube length required. The physical properties are as follows (H1): k = 15.6 W/m K, c,=149 J/kg K, u = 1.34 x 10-3 Pa s.
I was given this solution, Please advise on the solution
An ordinary egg can be approximated as a 5.5-cm-diameter sphere whose thermal conductivity of roughly k = 0.6- W mk overall density of p = 1000; and heat capacity of C₂ = 3000- kg m² The egg is initially at a uniform temperature of T₂ = 10°C and is dropped into boiling water at T.. = 90°C W - determine how long it will take for the egg to m²K Taking the convective heat transfer coefficient to be h reach T = 70°C. In solving the problem, please follow the steps below. For the Lump Model In solving this problem, please use the lump model method (ignoring the requirement of small Biot number and discuss the outcomes, 1. 2. Compute the characteristic length Lc Compute the volume and surface area of the sphere (as the egg model) Vol As 3. Compute the diffusivity α = = 10- k p Cp = J kgk Compute non-dimensional excessive temperature 0 = h Lc k 4. Compute the Biot number using the characteristic length found above Bi = T-Too 5. Ti-Too 6. Calculate the Fourier number from the equation =…
A composite plane wall consisting of materials, 1.5-in steel (k = 312 BTU-in/HR.ft2.0F) and 2-in aluminum (k = 1400 BTU-in/HR.ft2.0F), separates a hot gas at Ti = 2000F, hi = 2 BTU/HR.ft2.0F, from cold gas at To = 80 deg F, ho = 5. If the hot fluid is on the aluminum side, find: a) Transmittance, U; b) The heat through 100 sq. ft of the surface under steady state condition and c) The interface temperature at the junction of the metals.
I need the answer quickly
A food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at -25 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 0.5 cm, and a density of 980 kg / m3. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 50 W / (m? K). Calculate the freeze time.