2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number?

2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two inches of urethane foam will reduce heat loss close to 1000% when applied to a 2-inch diameter uninsulated steel pipe. Assume the pipe wall thickness is 0.25-inches, the pipe interior convective heat loss (hi) is 500 BTU/hr-ft2-oF, and the pipe outside convective heat loss ho 20 BTU/hr-ft2-oF, k steel is 25 BTU/hr-ft-oF, and k insulaton is 0.023 BTU/hr-ft-oF. (hint - calculate heat loss with and without insulation.
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D₁, 1 = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of D₁,2 = 250 mm and wall thickness to = 1;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k = 0.055 W/m-K) between the two pipes does not exceed its maximum service temperature of 7p,max = 70°C. The ocean water is at T, = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m²K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m².K. (2) It is proposed to enhance the performance of the…
20. The two plates of Problem 11 made of the same material and having constantk are exposed on one side to hot water at Tw and hw and on the other to cold air atTa and ha. Find a) the equation for temperature profile in these plates and b) temperaturesat x = 0 and at x = L if hw = ha = h. [Ans.: a) T1(x) = c1x + c2 where, c1 = hw(Ta – Tw)/c3 and c2 – Ta = – hw(haL +k)(Ta – Tw)/(hac3) where c3 = (k + hwL + hwk/ha)].
Stainless steel type 304 [k = 16.3 W/m-K] from heat treatment was brought to a room @ 27C. It is in cube form and has an edge of side 20cm. Initially, the temp. of the steel from the heat treatment is 500C. The total effective heat transfer coefficient is 18 W/m2-K. How long will it take for the surface of the cube to be within 28 C of the room temp.?
Consider the following data for a range of materials. In which of the following situations is creep likely to occur? Melting temperature of various materials: Melting Temperature (°C Material Ti alloy 1668 Carbon steel 1375 Alumina 2070 Nylon 66 polymer 262 A carbon steel component under continuous load in a power station operating at 200°C. A nylon pipe carrying fluid at 125K. All of the scenarios. A Ti alloy in a turbine operating at 350°C. An alumina ceramic component in a furnace operating at 600°C.
3. The starting length of a shaft is 25.00 mm. This shaft is to be inserted into a hole in an expansion fit assembly operation. To be readily inserted, the shaft must be reduced in length by cooling. Determine the temperature to which the shaft must be reduced from room temperature (20° C) in order to reduce its length to 24.98 mm. Refer to the Table below.
Thermal energy is being transferred through a 0.8 mm layer of human skin at a rate of 1.1 x 104 W/m?. The room temperature is 27 °C. (a) Determine the thermal conductivity of the skin.
"You did calculations using the simplified HAZ time-temperature formulas, assuming 3D heat flow, and are presenting your final internship conclusions to management. You realize with horror, in the middle of your presentation, that you forgot to label your calculated curves (below). Which curve is which? Pick the best answer A: "Plot 1 is HYPERFILL® and Plot 2 is p-GMAW. Since HYPERFILL® has the higher heat input, it cools more slowly." B: "Plot 2 is HYPERFILL® and Plot 1 is p-GMAW. Since HYPERFILL® has the faster travel speed of the two processes, it cools faster." C: "Plot 1 is p-GMAW and Plot 2 is HYPERFILL®. Since p-GMAW has the slower travel speed, it cools more slowly." D: "Plot 2 is p-GMAW and Plot 1 is HYPERFILL®. Since p-GMAW has the lower heat input, it cools faster" Both (A) and (D)
Name the two carriers of heat conduction through a metal. Provide at least one way you could modify a hypoeutectoid steel product to improve the first carrier, and then provide one way you could modify the same steel to improve the second carrier.
If temperature difference is doubled whereas thermal conductivity and wall thickness are halved, what will be change in heat conducted through wall?
Hello dear, I now have a very important test, and I need to answer in a short time, half an hour, and if you give me the answer within the specified time, I will like you in your answer and invite my colleagues also and thank you. Material resistance. I am waiting for you, sir, please