6.The crane at equilibriumsupports a weight of W=1 kN acting at G. The 8m-long horizontal boom DG has weight of W₁-2.5 kNand center of gravity at G₁ (the center of the boom).The crane (excluding the boom) has a weight ofW2-5 kN and center of gravity at G2. The cable KHis horizontal. The two wheels of the crane contactthe smooth 30° surface at A and B.(1) To determine the tension force in cable KH andthe reactions at A and B, please choose a proper FBand draw the FBD.(2) Determine the tension force in cable KH andthe reactions at A and B.1m1mG30°WW₁2m2m1mBi3mim30%

The horizontal component of Tension T is Tcos30 in the figure.I hope this is helpful.

Answered: 6. The crane at equilibrium supports a…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.29P: The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate...

See similar textbooks

Similar questions

The center of gravity of the 850-N man is at G. If the man pulls on the rope with a 388-N force, determine the horizontal distance b between the man's feet and G.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Determine the smallest horizontal force P that would push the homogeneous cylinder of weight W over the curb. Neglect friction.
The homogeneous 20-kg door is held in the horizontal plane by a thrust hinge at O, a hinge at A, and the vertical prop BC. Determine all forces acting on the door.
The pulley-cable system supports the 150-lb weight. The weights of the pulleys and the horizontal bar ABC are negligible. Determine the cable tensions at A and C and the distance x.
The cable AOB weighs 24 N/m. Determine the sag H and the maximum tension in the cable.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
The homogeneous cylinder of weight W = 100N rests in a frictionless right-angled corner. Determinethe contact forces NA and NB if θ = 30°.
The spring clamp of Fig. block Fagainst the floor. The force in the spring is F = k(e – lo), where e is the present length of the spring, lo = 3 in. is the unstretched length of the spring, and k = 240 lb/ft is the spring constant. Determine all forces acting on mem- ber ÁBC of the spring clamp and the force exerted by the spring clamp on the block E. is used to hold the 8 in. D E 8 in. 6 in -6 in.- 6 in.
Solve it fast within 10-15minutes ,Its easy one.
the tree feller cuts off large trees near ground level and then continues to grasp the trunk. Determine the force in hydraulic cylinder AB for the position shown if the tree weighs 6000lb. Determine the required pressure on the 4.72-in.-diameter piston of the cylinder. draw the free body diagram

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L