Question 8Take E 160 GPa and I = 56(106) m².(Figure 1)Figure10 kN/m6 m-B-6 m1 of 1Part ADetermine the reaction at the roller support B if it settles 5 mm.Express your answer to three significant figures and include the appropriate units.НАBy = ValueUnitsSubmitRequest Answer< Return to AssignmentProvide Feedback?

Answered: Image /qna-images/answer/31f746cf-7681-4f0d-837d-a5672bd19bbf.jpg

Answered: Question 8 Take E 160 GPa and I =…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the toggle clamp shown in (Figure 1). Figure -235 mm- 30 mm 70 mm 30 mm D 30 30 E Part A If a clamping force of 350 N is required at A, determine the magnitude of force F that must be applied to the handle of the toggle clamp. Express your answer to three significant figures and include the appropriate units. F = - 1370 Submit μÃ Provide Feedback ^ X Incorrect; Try Again + N • 5) ? Previous Answers Request Answer Next >
Please use ANSYS SOFTWARE
I need to find the forces in each tube but I keep getting stuck. I have been getting really long equations to do algibra onwhich I suspect might be where the error was comming from. The values I have tried are F2 = -0.97786, and -4.889 kips
10:59 A A circular steel shaft has a radius of 0.05 m. The shaft is supported by rollers at A and B. F₁ F₂ JIL D d₁ Variable d₁ F₁ F₂ d₁ F3 Values for the figure are given in the following table. Note the figure may not be to scale. Value 1.1 m wamap.org 460 N 240 N 550 N d₁ F3 E d₁ B a. Determine the reaction force at point A, Ay. b. Determine the reaction force at point B, By. c. Determine max internal bending moment on the beam, Mmax: i. Hint: It occurs at the center. Make a cut to the left of point D. Then doΣM = 0 d. Determine the moment of inertia of the shaft, I. e. Determine the magnitude of the max bending stress in the shaft, max
Part A Consider the mechanism shown in (Figure 1). FA = Submit 0 ■ μÅ -235 mm Value 30 mm 30 mm/ If a force of F = 350 N is applied to the handle of the toggle clamp, determine the resulting clamping force at A. Express your answer to three significant figures and include the appropriate units. 70 mm Request Answer B 30 Units F 30% 275 mm ] ?
The frame in (Figure 1) supports the 600-lb load. The pulley at C has a radius of 0.5 ft. The pulley at D has a radius of 0.25 ft. Figure 4 ft 60% - 30° 30° 3 ft ▼ ▼ Part A Determine the reaction at pin A. Express your answer in pounds to three significant figures. FA = Submit Part B FB = VAX 1 vec A Determine the reaction at pin B. Express your answer in pounds to three significant figures. Submit Request Answer VAZ Ivec S Request Answer < Return to Assignment Provide Feedback ? ? lb lb
I tried this problem but I have no idea on how else I am sapposed to get the distance s than the method I tried so I'm at a loss can you show me how I can get this distance please?
- Please Provide Free Body Diagrams and Kinetic Diagrams.- Please state all equations in variable form first before substituting values for the variables.- Please show EVERY step of the solution, including all steps necessary to solve systems of equations.- once answered Correctly will UPVOTE!!
I Rev Consider the truss shown in (Figure 1). Suppose that F = 6 kN, F2 = 8 kN and F3 = 9 kN Part A Determine the x and y components of reaction at A using scalar notation. Express your answers using three significant figures separated by a comma. vec ? Az, Ay = 10.667 kN Figure 1 of 1 Submit Previous Answers Request Answer Part B Determine the y component of reaction at B using scalar notation. 2 m Express your answer to three significant figures and include the appropriate units. B ? HA F, 2 m 2 m 2 m By = Value Units Submit Request Answer Pearson
Posted this 2 times and a wrong answer was given twice ….. Pls do if u know it
The shaft of the motor M turns with an angular velocity w = 100(4+t) rad/s, where t is in seconds. (Figure 1) Figure 50 mm D 300 mm 30 mm 225 mm W 40 mm M 1 of 1 Part A Determine the distance the load W is lifted in t = 5 s using the hoist. Express your answer to three significant figures and include the appropriate units. SW = Submit O μA Value Provide Feedback Request Answer Units ?
Do not copy else where they are wrong pls find what’s in yellow only

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS