Q8 In an ideal constant volume cycle the pressure and temperature at thebeginning of compression are (103bar) and (50 °C) respectively and the compressionratio (8:1). The heat supplied during the cycle is (840Kj/Kg) of working fluid.Determine (a) the maximum temperature attained in cycle. (b) the thermal efficiencyof the cycle. (c) the work done in Kj during the cycle per Kg of working fluid.Answers (a) 1925 K, (b) 56.4 %, (c) 474.36 Kj/Kg

Answered: Image /qna-images/answer/4a918cd8-f015-45f8-a451-6df0619264c3.jpg

Answered: Q8 In an ideal constant volume cycle…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The working fluid of a liquid-vapor cycle is 1kg of R-134a (Hint: Use the R-134a thermodynamic tables.) The cycle operates between two pressures 100kPa and 1000kPa. Process A-B: An isobaric compression at the high pressure from a saturated vapor to a saturated liquid. • ProcessB-C: An iso-entropic process from the high pressure to the low pressure. • Process C-D: An isobaric expansion at the low pressure. •Process D-A: An iso-entropic process from the low pressure to the high pressure. •a) Make a table of the temperature, pressure, volume, internal energy, enthalpy, entropy and quality factor (T, P, V, U, H, S & x) at the start of each process. b) Make a table of the change in internal energy, heat flow, work done, change in enthalpy, and change in S) during each leg of the cycle.AH, AU, Q, W, Aentropy (c) Draw a well-labeled T-S diagram (indicating lines of constant pressure and the saturation dome.) d) Calculate the coefficient of performance of the cycle "nglish (United States)
Please please solution
Carnot cycle heat pump utilizes R-134a as the working fluid. Heat is transferred from the fluid at 100 F, and during this process the refrigerant changes from saturated vapor to saturated liquid. Heat transfer for the refrigerant takes place at 20 F. You are asked to do the following: (a) Show and describe the cycle on a T-s diagram (b) Calculate the quality at the beginning and at the end of the isothermal process at 20 F (c) Determine the coefficient of performance for the cycle.
Air within a piston-cylinder assembly executes a Carnot heat pump cycle, as shown in the figure below. For the cycle, TH = 400 K and Tc = 300 K. The energy rejected by heat transfer at 400 K has a magnitude of 625 kJ per kg of air. The pressure at the start of the isothermal expansion is 325 kPa. TH Te p-v diagram for a Carnot gas refrigeration or heat pump cycle. Assuming the ideal gas model for the air, determine: (a) the magnitude of the net work input, in kJ per kg of air, and (b) the pressure at the end of the isothermal expansion, in kPa.
The compression ratio of an engine working on the constant volume cycle is 9.3. At thebeginning of compression, the temperature is 31°C and at the end of combustion thetemperature is 1205°C. Taking the compression and expansion process to be adiabatic andthe value of k as 1.4. Determine the following a. T2. 741.7657 Kb. T4. 605.733 Kc. Thermal Efficiency. 59.02%
An ideal Stirling cycle cooler, using helium (considered ideal) as its working fluid, has a compression temperature Tc=32°C and an expansion temperature TE=-21°C. If state 1, at the beginning of the compression, is defined with a volume V1=40 cm3 and a pressure P1=1.8 MPa, and state 2 is defined with a volume V2=33 cm3, what is the heat qɛ absorbed during the expansion process (in Joules)?
The Otto cycle should be used to model an engine cycle. Every one of thepresumptions of the ideal Otto cycle should be applied aside from that a polytropicinteraction with n 1.3 will be utilized for the expansion process. The conditionstoward the beginning of pressure is T1 = 333 K, P1 is 90 kPa and the compressionratio is 8. The energy infused into the cycle during the consistent volume process is2000 kJ/kg. Assume constant specific heatsa) Find the expansion work (kJ/kg)b) Find the net heat transfer for the cycle (kJ/kg) diesel
Air within a piston-cylinder assembly executes a Carnot heat pump cycle, as shown in the figure below. For the cycle, TH = 600 K and Tc = 300 K. The energy rejected by heat transfer at 600 K has a magnitude of 1000 kJ per kg of air. The pressure at the start of the isothermal expansion is 325 kPa. p-v diagram for a Carnot gas refrigeration or heat pump cycle. Assuming the ideal gas model for the air, determine: (a) the magnitude of the net work input, in kJ per kg of air, and (b) the pressure at the end of the isothermal expansion, in kPa.
Q3] Consider a combined gas-steam power cycle as shown in the following figure. The gas turbine cycle has a pressure ratio of 7. Air enters the compressor at 27°C at a rate of 12 kg/s and at the gas turbine at 1027°C. The heat rate transferred at the heat exchanger is 5300 KJ/s. The steam leaving the pump is saturated water at 20 bar and enter the steam turbine as a saturated steam. Determine: 1- The air temperature at point 5 2- Work done by the compressor in KJ/kg. 3- Work done by the gas turbine in KJ/kg. 4- Flow rate of the steam in kg/s. 5- If the work produced by the steam turbine is 0.3 of that produced by gas turbine, determine the overall efficiency (ignore the pump work). 2 Comp. 1 47 Pump 40 6 C.C 3 Heat Exchanger 5 Condenser 4 9 8 4 ST GT 4
Consider a heat engine is operating on a steady‐flow Carnot cycle with water asthe working fluid. The water mass flow rate in cycle is 0.5 kg/s. The cyclemaximum per minimum absolute temperatures ratio is 2.5. The quality of wateris 1 at the beginning of the heat‐rejection process and 0 at the end and theambient temperature is 35°C. Show the cycle on a T‐s and P‐v diagrams relativeto the saturation lines, and determine (a) the thermal efficiency, (b) thepressure at the turbine inlet, (c) maximum temperature, minimum pressure (d)the network output, (e) the entropy changes in all processes, and (f) the actualnetwork output with second law efficiency of 45%.
DIESEL CYCLE: 1. Air in an ideal Diesel Cycle is compressed from 3 L to 0.15 L and then it expands during the constant pressure heat addition process to 0.3 L. Under cold air Standard conditions, the thermal efficiency of this cycle is:
Instead, assume variable specific heat An ideal Otto cycle has a compression ratio of 8. Atthe beginning of the compression process, air is at 95 kPaand 278C, and 750 kJ/kg of heat is transferred to air dur-ing the constant-volume heat-addition process. Taking intoaccount the variation of specific heats with temperature,determine (a) the pressure and temperature at the end ofthe heat-addition process, (b) the net work output, (c) thethermal efficiency, and (d) the mean effective pressure forthe cycle.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS