Q1: The overall volume expansion ration of a Carnot cycle is 15/1. The temperature limits of the (260° C) and (21°C). Determine: A) The volume ratio of the isothermal and adiabatic processes. B) The thermal efficiency of the cycle. (y = 1.4)

Q1: The overall volume expansion ration of a Carnot cycle is 15/1. The temperature limits of the (260° C) and (21°C). Determine: A) The volume ratio of the isothermal and adiabatic processes. B) The thermal efficiency of the cycle. (y = 1.4)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Task3
Choose correct answer: When the cylinder is cushioned at the end of the stroke, how does cushioning affect the piston's force? At the beginning of the stroke, cushioning increases the piston's force. At the beginning of the stroke, cushioning reduces the piston's force. At the end of the stroke, cushioning increases the piston's force. At the end of the stroke, cushioning reduces the piston's force.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
help[
please put it on paper. thank you
Hello sir, I want to solve in a clear beautiful font that will be a manual line with a pen I know a strange request and don't forget my name and thank you sir, God bless you
Please show all steps
What’s the correct answer please?
Table 1: Mechanical behavior of human cadaver tibial bones during pure torsional loads applied with the proximal tibia fixed and the torque applied to the distal tibia until there is bone fracture. Medial condyle Tibial tuberosity- Medial malleolus -Lateral condyle Head of fibula Ti-6Al-4V grade 5 Stainless Steel 316L Region of bone resection -Lateral malleolus L = 365 mm Annealed Annealed Torque at ultimate failure (bone fracture) Displacement (twist angle) at ultimate failure Torsional Stiffness Table 2: Mechanical properties of candidate materials for the rod. Material Process Yield Strength (MPa) 880 220-270 Do = 23 mm Elastic Modulus (GPa) 115 190 d₁ = 14 mm Figure 1: Representative tibia bone showing the resection region (blue arrows) and median length (L). A circular cross section of distal tibia taken at the level of resection) showing the median inner (di) and outer (Do) diameters of the cortical bone. A tibia bone after resection with the proposed metal solid rod (black line)…
Through the following formulas: (100-FGM) DP 100-IGM WGI= where: WGI - Wet grain input in ton/h DP-Dryer performance in ton/h FGM - Final grain moisture in % IGM - Initial grain moisture in % EP =WGI-DP where: EP - Evaporation power in ton+₂0/h EC = GC HP where: EC - Energy consumption in kcal/h GC-gasoil consumption in kg/h HP-heating power of gasoil in kcal/kg SEC where: SEC - Specific energy consumption in kcal/kgH20 Select which of the following specific energy consumption options correspond to a dryer that has a performance of 40 tons/h, and is required to reduce grain moisture from 17% to 13.5%. Data: EC EP-1000 heating power of gasoil-10100 kcal/kg gasoil consumption=213 kg/h Answer 500-1000 kcal/kg H20 1500-2000 kcal/kg H20 1000-1500 kcal/kg H20 O O O
help num3 please,badly need ittt