Consider the following piping system of 1-nominal schedule 40 galvanized steel that conveys water with a volumetric flow rate of 15gpm. N 1. basket strainer 2.1'-0" 3.0-9° 4.3-0 5.1'-1' 6.1'-6" 7.0-10° 8.1-2 9.3-1° 10.1'-5" 11.2-1" 12.45° ells 10 All fittings in the system are threaded. The loss coefficient for the basket strainer can be approximated with K-1.3. As the engineer on the job, you are tasked the conduct the, following calculations and analyses: 3) Calculate the magnitude of power needed to move this fluid at 15gpm.

Consider the following piping system of 1-nominal schedule 40 galvanized steel that conveys water with a volumetric flow rate of 15gpm. N 1. basket strainer 2.1'-0" 3.0-9° 4.3-0 5.1'-1' 6.1'-6" 7.0-10° 8.1-2 9.3-1° 10.1'-5" 11.2-1" 12.45° ells 10 All fittings in the system are threaded. The loss coefficient for the basket strainer can be approximated with K-1.3. As the engineer on the job, you are tasked the conduct the, following calculations and analyses: 3) Calculate the magnitude of power needed to move this fluid at 15gpm.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter8: Leak Detection, System Evacuation, And System Cleanup

Section: Chapter Questions

Problem 2RQ: Name and briefly describe the six classes of leaks.

See similar textbooks

Similar questions

ive already sent this prioblem, please redo by hand as requested as it is easier for me to follow, and also not from chat gbt thanks
Give solution asap , Handwritten required.
No. 1: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with a volume of water equal to twice that contained in the system. How much water (number of gallons) must be flushed through the system. (1ft3 = 7.481 gallons)
7.45 If the fluid motor has an efficiency of 78 percent, how much power is delivered by the motor? 15-in Schedule 80 steel pipe 25-in Schedule 80 steel pipe Oil -Motor Flow 38.5 in Mercury sg = 13.54 Answer is 1.24 Hp. Please shw how to get ture.
What size of receiver tank (gal) for a compressor is required if the pneumatic system is used to drive 5 linear cylinders which collectively consume 12 SCFM for 5 minutes? The compressor pressure switch operates between 90 and 110 psi.
FROM THE ATTACHED SKETCH, THE GIVEN DATA ARE AS FOLLOWS: Pressure loss due to friction a. Reservoir tank =50,000 liters of water b. Total Static head is 30 ft. Pressure loss in plastic pipes (feet of water per 100 ft of tube) c. Pipe material is plastic and 1.5-inch diameter. d. There are four 90-degree elbows, one gate valve and one open swing spm 0.5 in. 0.75 in. 1 in. 1.5 in. 2 in. 3 in. 1.4 4.8 0.0 0.0 0.0 0.4 0.1 0.4 0.8 1.3 1.9 2.7 0,0 0.0 valve. 0.0 1.2 2.5 4.2 6.3 8.8 15.2 26.0 49.7 86.9 e. Total pipe length is 50 ft. 3 0.0 10.0 17.1 25.8 36.3 63.7 97.5 0.0 0.1 0.2 0.2 0.3 4. 0.0 0.0 5 0.0 0.0 0.0 0,0 0.0 6 0.1 0.2 0.3 0.5 0.9 0.1 COMPUTE THE FOLLOWING USING THE PROVIDED TABLE BELOW. 8 4.6 0.6 10 15 20 6.9 14.6 0.8 1.7 2.9 0.0 25.1 1. IF THE TANK IS TO BE FILLED WITHIN 661.35 MINUTES WHEN EMPTY, COMPUTE HOW MANY GALOONS PER MINUTE (GPM) PUMP CAPACITY IS NEEDED TO FILL UP THIS TANK., USE 3.78 LITERS/GAL Pressure loss in valves and elbows (expressed in equivalent length of tube)…
Problem 3: A submersible deep-well pump delivers 745 gal/ h of water through a 1-in Schedule 40 pipe when operating in the system sketched in the figure below. An energy loss of 10.5 lb-ft/lb occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency. Air Storage tank 40 psig Vent Well Flow casing 120 ft Well level Pump
What is the rate of flow of water passing through a pipe with a diameter of 20mm and a speed of 0.5m/sec?
Solve fast
The meter-out circuit shown below has cylinder which has a 4 square inch piston area and a rod with a 2 square inch cross sectional area. The pressure relief valve setting is 3000 psi and the pump always produces more than flow than the flow control valve will allow through it. If the load is 4,619 Ibs overrunning, what is the pressure (in psi) in the rod end of the cylinder. Assume no pressure drop across the DCV. P1 4 in P3 P2 J. 3000 psi 2 in
A cylinder is configured with a flow control valve to meter-out during extension. The cylinder is a 2" bore and 1" rod. The pump flow rate is 5 gpm with a pressure reducing valve set to 1500 psi. The load is 500 lbs. If the extension speed is to be limited to 10 in/s, what pressure would be measured on the retraction side of the cylinder, during extension? Enter a whole number.
2. Common Fluids Conversions - Please calculate the following: a. 50 GPM to ft/s in a 4" Sch 40 pipe b. 15 GPM to lbm/s of Chloroform at 25°C 30 psi to ft lb-/lbm of Water at 50°C 40 ft lbf/lbm to hp of a fluid moving at 150 lbm/min. Reynolds number for 100% Glycerol at 75°C flowing through a 2.5" Sch 80 pipe at 10 lbm/s d. e.