Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. (Figure 1) Part A If a force is applied to the end B of the member and causes it to rotate by 0 = 0.40°, determine the normal strain in the cable. Express your answer in millimeters per millimeter to three significant figures. Figure 600 mm- To BO P 800 mm ΜΕ ΑΣΦ ↑ vec € AB = Submit Request Answer < Return to Assignment Provide Feedback 1 of 1 ? mm/mm

Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. (Figure 1) Part A If a force is applied to the end B of the member and causes it to rotate by 0 = 0.40°, determine the normal strain in the cable. Express your answer in millimeters per millimeter to three significant figures. Figure 600 mm- To BO P 800 mm ΜΕ ΑΣΦ ↑ vec € AB = Submit Request Answer < Return to Assignment Provide Feedback 1 of 1 ? mm/mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Similar questions

A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
My answer is displayed and incorrect. Please give answer in ksi.
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 1.6°. The wires are unstretched when the lever is in the horizontal position. (Figure 1) Figure A 200 mm G ,200 mm 300 mm- -H C FY 200 mm 300 mm D E 1 of 1 Part A Determine the average normal strain developed in wire AH. Express your answer using three significant figures. ΠΑΣΦ Τ (EAH) avg= Submit Part B (ECC) avg= Determine the average normal strain developed in wire CG. Express your answer using three significant figures. Submit Part C Request Answer (EDP) avg= vec • VAΣo↓ vec ΠΙΑΣΦΑ Request Answer 4 Determine the average normal strain developed in wire DF. Express your answer using three significant figures. ΠΑΣΦΑ vec ↑ ? ? ? mm/mm mm/mm mm/mm
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If the load P on the beam causes the end C to be displaced 8 mm downward, determine the normal strain developed in wire CE. (Figure 1) ECE = Submit ▾ Part B EBD = Submit V—| ΑΣΦ Determine the normal strain developed in wire BD. Provide Feedback Request Answer ΑΣΦ vec Request Answer vec SO ? ? mm/mm mm/mm Next >
The strain rosette shown below was used to obtain normal strain data at a point on the free surface of a 2024-T4 aluminum alloy machine part. The gage readings were Ea = +630μ, b = +450μ, and Ec = +1200μ. Determine (a) The strain components Ex, Ey, and Yay at the point. (b) The stress components o, y, and Tay at the point. Express the stresses in SI units. (c) The principal stresses and the maximum shearing stress at the point. Gage c Y 90° Gage b Gage a 45° -X
The rectangular plate is deformed into the shape shown by the dashed lines. Suppose that a = 330 mm and b = 370 mm. (Figure 1) PART A) Determine the average normal strain along diagonal BD.Express your answer using three significant figures. PART B) Determine the average shear strain γxy at corner B relative to the x, y axes..Express your answer to three significant figures and include the appropriate units.
The state of strain at the point on the arm in Figure Q10 has components ϵx = 200.5 micro-strain, ϵy = 324.4 micro-strain, and γxy = 220.6 micro-strain (1 micro-strain = strain×10-6). Figure 10 Calculate the maximum principal strain. Express your answer in micro-strains. Report your answer to 1 decimal place.
Q4 A three strain gages have been attached directly to a piston used to raise a medical chair, the strain gages give strains as Ea = 80 µ , Eb = 60 µ and Ec = 20 u . Determine the principal strains and the principal strain directions for the given set of strains. And Compute the strain in a direction -30° (clockwise) with the x axis. 45 Pump
pleae writte by hand step by step
Please help me with part a and part B thanks Use image below box your answers with correct units
2a. The delta strain gauge rosette shown in Figure 2a is attached to a structural component and measures the following strains: ɛ = 775x10°, ɛz = 415x106, ɛ̟ = -515x10°. Determine the principal strain and principal stress components in both magnitude and direction given that the structure has a Young's Modulus of E = 200×10° N/mm? and Poisson's ratio of v = 0.3. Show the directions of the principal stresses on a properly oriented stress element relative to the x,y coordinate system. 60° 60° 60° Figure 2a