A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10 in. to new position Q' as shown. Determine the magnitude of the shear strain at Q' associated with the two edges (PQ and QR). P 25 in. 7982 μrad 6862 μrad 9533 μrad 06186 μrad O8600 μrad 4 in. R 10 in. L X

A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10 in. to new position Q' as shown. Determine the magnitude of the shear strain at Q' associated with the two edges (PQ and QR). P 25 in. 7982 μrad 6862 μrad 9533 μrad 06186 μrad O8600 μrad 4 in. R 10 in. L X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal AC. D C 6 mm 4 mm 20 mm A 20 mm
If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal AC. D 2 mm 3 mm 15 mm A B 15 mm Select one: 0.0853 0.0607 0.1402 0.1281 0.0467 K
6. Airplane components often have a “stressed skin" construction, which consists of a thin sheet of aluminum in tension connected to the structure with rivets (i.e. pins that go through circular holes). a. If the aluminum skin is subject to a far-field biaxial tension of σ = 100 MPa and has a yield strength of σ = 210 MPa, will the rivet cause the sheet to yield? b. What is the strain through the thickness (z-direction) at the top-most edge of the hole? What does this mean is happening to the plate at that point? c. If a crack of length a = 1 mm forms at the side of the hole, will the plate fracture? How about if the crack is a = 3 mm? Take the aluminum to have a fracture toughness of K₁c = 15 MPa√m, and take the geometric stress concentration factor to be Y = 1.12. 50 = a
please help me with this question i got someone else to help me and they got the wrong answer now i only have one attempt please help me get the right answer thank you
Please answer in proper units
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.4 lb/in.³ is the specific weight of the material, y = 1.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 9 in. is the length of the bar, and E= 26000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar. Calculate the change in length of the bar due to its own weight. Answer: x10-6 in.
Q1 The 45° strain rosette is mounted on a steel robotic am as shown in Figure Ql. The robotic arm is made from steel with Esel = 200 GRA and poison ratio, v= 0.3. The following readings are obtained for each gauge: E=[Y+Z](10“) E = -250(10-) E= -200(10) Here the value of Y and Z depends on the 5th digit and 6th digit of your matric number as shown in Table 1. For example, if your matrix number is DD 070112 gives the value of Y=300 and Z-60: Table 1 5 digit of matric 6* digit of matric number number 250 300 350 30 2 60 3 400 3 90 4 450 120 5 500 150 6. 550 180 7 600 7 210 650 700 240 270 (a) Prove that &= E, and E, = E. Determine the shear strain, yand the normal strain, E, and &. (b) Estimate the in-plane principal strains and the angle associated with the principal strains, and (c) Calculate the principal stress associated with the prihcipal strains in (c). (d)
This course EHide blocks If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal AC. C 1 mm 2 mm 10 mm A В 10 mm Select one: O 0.0793 O 0.1402 O 0.1281 0.0382 9:15 PM EN 4/15/2021
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 3.6 x 10-³. Solution Cross-sectional Area, A (in mm²) = 63.617 One possible correct answer is: 63.617251235193 Tensile Stress, (in N/mm²) 723.6 One possible correct answer is: 723.6 Tensile Load, (in N) = = 46033.261 One possible correct answer is: 46033.442993786 Length of the Specimen (in mm) 4.366 X One possible correct answer is: 277.77777777778
Which of the following has no unit * O strain surface tension O elasticity
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
O 0.6% 19% If an isotropic material has a Young's modulus of 85 Gpa and a Poisson's ratio of 0.25, calculate its shear modulus. Select one: O G = 29 Gpa O G = 34 Gpa G = 25 Gpa O G= 77 Gpa O G= 46 Gpa If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal BD. C 2 mm 4 mm EN DO O