2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and agage length of 2 in. is shown in the figure below.TENSILE STRESS (MPA)45040035030025020015010050Part A00STRESS VS. STRAIN0.0020.004STRAIN0.006Determine the modulus of resilience. Show units.Part BDetermine the modulus of elasticity of the material.Part C Estimate the Yield Strength of the material.0.0080.01

Answered: Image /qna-images/answer/0b02a60a-3a3a-43df-b80e-61d38feb4e46.jpg

2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 STRESS VS. STRAIN 0.002 Part C 0.004 STRAIN 0.006 Part A Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Estimate the Yield Strength of the material. 0.008 0.01

2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a gage length of 2 in. is shown in the figure below. TENSILE STRESS (MPA) 450 400 350 300 250 200 150 100 50 STRESS VS. STRAIN 0.002 Part C 0.004 STRAIN 0.006 Part A Determine the modulus of resilience. Show units. Part B Determine the modulus of elasticity of the material. Estimate the Yield Strength of the material. 0.008 0.01

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The stress-strain diagram for a steel alloy having an original diameter of 0.80 in. and a gage…

Q: Channel AB is fixed in space, and its centerline lies in the xy plane. The plane containing edges AC…

A: Write the given data. m=1.6 kg Draw the free-body diagram of sphere E.

Q: Part A The rectangular plate undergoes a deformation shown by the dashed lines where D = 4 in. dj =7…

Q: Based on the information above; draw stress-strain diagram of the material and answer the following…

Q: The stress-strain diagram for a steel alloy having an original diameter of 0.80 in and a gage length…

A: Given data Original diameter = 0.8 in Gage length = 10 in Find the load at yielding point.

Q: The allowable tensile stress for wires AB and AC is allow 190 MPa. The applied load is P = 7.8 kN.…

A: Given that: Maximum allowable stress = 190 MPa The applied load P = 7.8 kN For the given…

Q: The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

A: Given ,A alluminium specimen in which guage length = 50 mm and diameter of 12.5 mmLoad applied = 45…

Q: The curve is linear between the origin

A: Stress - Strain curve shown below for the given values.

Q: A hot rolled steel tension test sample has a diameter of 6 mm and the original gage lenght of 30 mm.…

A: Original diameter of the specimen, Do=6mm Original Length of the specimen, Lo=30mm Fracture…

Q: Q2] ( 12 Marks) A specimen of magnesium having a rectangular cross section of dimension 3.2 mm x…

A: GivenArea=3.2mm×19.1mmlength=63.5

Q: A cylindrical specimen of a steel alloy having a diameter of 12.8 mm and a gauge length of 50.8 mm…

Q: A steel [E = 200 GPa] rod with a circular cross section is 13-m long. Determine the minimum diameter…

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

Q: The following data were obtained during a tensile test of an alluminium alloy specimen. Initial…

A: Given data:

Q: tress-strain diagram for a steel alloy having an original diameter of 0.80 in. and a ength of 2 in.…

Q: A bar having a length of 125 mm and cross-sectional area of 467.5 mm² is subjected to an axial force…

Q: How can I solve for the %0.2 offset strain and the calculated stress? Original diameter : 6mm…

A: Stress is ratio of force applied on a material to the material's cross-sectional area. Strain is…

Q: Problem F2 stress (ksi) 130 120 110 100 90- 80 70 60 50 40 30 20 10 0 0.000 0.025 0.050 0.075 0.100…

A: The elastic modulus is E=29000 ksi. The diameter of the cylindrical specimen is d=2 in

Q: A titanium alloy (Ti-5Al-2.5Sn) specimen with the dimensions shown below is subjected to a uniaxial…

A: The stress of a bar is given by, , where P is the normal load and A is the cross-section area of…

Question

2) The stress-strain diagram for an alloy specimen having an original diameter of 0.5 in. and a
gage length of 2 in. is shown in the figure below.
TENSILE STRESS (MPA)
450
400
350
300
250
200
150
100
50
Part A
0
0
STRESS VS. STRAIN
0.002
0.004
STRAIN
0.006
Determine the modulus of resilience. Show units.
Part B
Determine the modulus of elasticity of the material.
Part C Estimate the Yield Strength of the material.
0.008
0.01

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the proportional limit. Stress (ksi) 40 30- 20 10- 0- 0.0 0.0 Upper scale 0.020 0.002 22 ksi O 15 ksi E 19 ksi O 10 ksi 13 ksi Lower scale- 0.040 0.060 0.080 0.100 0.004 0.006 0.008 0.010 Strain (in./in.) 0.120 0.012
o (MPa) 900 800 700 600 500 400 300 200 100 0 0 0.01 0.02 0.03 0.04 0.05 0.06 0.07 0.08 0.09 Question 1 Which ONE of the following descriptions is TRUE for this material? Its yield stress is approximately 720 MPa. It is a brittle material. It is a ductile material. Its ductility as a percentage elongation is approximately 0.6%. E
submit to blackboard. 1- The stress-strain diagram for human tendon having an original diameter of 0.8 cm. and an initial length of 3 cm. is given in the figure. a) Determine approximately the modulus of elasticity for the material (E?). b) Determine the load (Pvield) on the specimen that causes yielding (make sure to include the yielding stress (o,) in the answer). c) Determine the ultimate load (Pultimate) the specimen will support (make sure to include the ultimate stress in the answer). MPа 70 60 50 40 30 20 10 10-3 80 & 0. 20 40 60 (Ans: because it needs reading from a graph and the final answer is estimation and not unique, the final results are not given)
A tensile test is being conducted on a steel-rod specimen with a gauge length of L0=4.0 in and an initial diameter of d0=0.75 in. If the final length of the rod at fracture is Lt= 5.53 in, find the percent elongation of the rod at fracture
Determine the elastic modulus and the yield strength for the material having the stress-strain curve shown. Use the 0.2% offset method. 1600 1400 1200 E 1000 800 600 400 200 0.5 1 1.5 2 Strain, percent Elastic modulus: (Express your answer in whole numbers.) E = ksi Yield strength: (Express your answer using three significant figures.) Sy = ksi Stress, psi
Elastic Properties of Materials 4. A cylindrical bar of steel 10 mm (0.4 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Using the data in Table given below, determine the force that will produce an elastic reduction of 3 × 10¯³mm (1.2 × 10-4 in.) in the diameter. Metal Alloy Aluminum Brass Copper Magnesium Nickel Steel Titanium Tungsten Modulus of Elasticity GPa 69 97 110 45 207 207 107 407 106 psi 10 14 16 6.5 30 30 15.5 59 Shear Modulus GPa 25 37 46 17 76 83 45 160 106 psi 3.6 5.4 6.7 2.5 11.0 12.0 6.5 23.2 Poisson's Ratio 0.33 0.34 0.34 0.29 0.31 0.30 0.34 0.28
Answer should be in MPa
1. For the stress-strain curve shown below, please estimate the properties indicated. (a) Fracture Strain Please do your work on a separate sheet of paper, and put your answers in the boxes on the right. Be sure to include the proper symbol and units. Stress Strain 70 60 50 Stress (ksi) 240 30 20 10 70 0 0.000 60 50 Stress (ksi) 40 20 10 KULL 0 0.000 0.010 0.050 0.100 Strain (in/in) Stress Strain 0.020 0.030 Strain (in/in) 0.040 0.150 0.050 (b) Ultimate Tensile Stress (c) Fracture Stress (d) Proportional Limit (e) Elastic Modulus (1) Yield Stress (g) Tensile Toughness (Modulus of Toughness) (h) Modulus of Resilience
640 480 160 0.002 0,004 0.006 0.008 0.010 Strain (mm/mm) A tensile test specimen of Aluminum alloy having a gauge length of 280 mm was tested to fracture. Stress and strain data obtained during the test are shown in the attached Figure. **Answers are approximate - do your best to read the graph. Determine: (a) the modulus of elasticity in GPa (4sigs). Enter this value into D2L answer box. (b) the proportional limit in MPa (3sigs). (c) the ultimate strength in MPa (3sigs). (d) Ductility of material based on percent elongation. (3sigs) Your Answer: Stress (MPa)
A specimen of magnesium having a rectan- gular cross section of dimensions 3.2 mm × 19.1 mm (in. × in.) is deformed in ten- sion. Using the load-elongation data tabulated as follows, complete parts (a) through (f). lbf 0 310 625 1265 1670 1830 2220 2890 3170 3225 3110 2810 Load N 0 1380 2780 5630 7430 8140 9870 12,850 14,100 14,340 13,830 12,500 in. 2.500 2.501 2.502 2.505 2.508 2.510 2.525 2.575 2.625 2.675 2.725 2.775 Fracture Length mm 63.50 63.53 63.56 63.62 63.70 63.75 64.14 65.41 66.68 67.95 69.22 70.49 (a) Plot the data as engineering stress versus engineering strain. (b) Compute the modulus of elasticity. (c) Determine the yield strength at a strain offset of 0.002. (d) Determine the tensile strength of this alloy. (e) Compute the modulus of resilience. (f) What is the ductility, in percent elongation?
Determine the percentage of ductility of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 450 400 350 300 250 200 150 100 NO 50 0.05 0.1 0.15 0.2 0.25 0.3 0 35 0.4 Strain 300 EN Stress (Mpa)