Problem F2 stress (ksi) 130 120 110 100 90- 80 70 60 50 40 30 20 10 0 0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 strain (in/in) Above you will find the experimental stress-strain diagram of 1045 steel. Calculate the permanent set if a cylindrical specimen with a diameter of 2 in is loaded to the ultimate stress and then unloaded. Provide your answer in units of in/in with 3 significant figures after the decimal. The elastic modulus of 1045 steel is 29,000 ksi.

Problem F2 stress (ksi) 130 120 110 100 90- 80 70 60 50 40 30 20 10 0 0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 strain (in/in) Above you will find the experimental stress-strain diagram of 1045 steel. Calculate the permanent set if a cylindrical specimen with a diameter of 2 in is loaded to the ultimate stress and then unloaded. Provide your answer in units of in/in with 3 significant figures after the decimal. The elastic modulus of 1045 steel is 29,000 ksi.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
1.4-7 The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13 mm and a gage length of 50 mm (see figure for Prob. 1.4-3). At fracture, the elongation between the gage marks was 3.0 mm and the minimum diameter was 10.7 mm. Plot the conventional stress-strain curve for the steefor the steel and determine the proportional limit, modulus of elastics of elastic- ity (i.e., the slope of the initial part of the stress-strain,tress-strain curve), yield stress at 0.1% offset, ultimate stress, percent, elongation in 50 mm, and percent reduction in area. 'ess, percent area. TENSILE-TEST DATA FOR PROB. 1.4-7 Elongation (mm) 0.005 0.015 0.048 Load (kN) 5 10 30 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture
Can i get help with these problems
A material has a stress-strain behavior shown in the Figure below. What is the material strength at rupture? What is the toughness of this material?
I need the solution please
solve first one only and use b h and x to find the strain
5. Consider a cylindrical specimen of a steel alloy (Figure 6.22) 10 mm in diameter and 75 mm long that is pulled in tension. Determine its elongation when a load of 20,000 N is applied. Stress (MPa) 600 500 400 300 200 100 0 0.00 0.04 Stress (MPa) 500 400 300 200 100 0.000 0.002 0.004 0.006 0.08 Strain Strain 0.12 0.16 0.20 Figure 6.22 Tensile stress-strain behavior for a steel alloy.
1. A bicycle wheel is assembled with each spoke pre-tensioned to a tensile force of 95 lbf. The diameter of each spoke is d = 0.0787 in. After the wheel is assembled, a strain gauge is applied to a representative spoke so that the gauge reads zero strain in the pre-tensioned condition. The figure below shows one cycle of strain readings as the wheel rotates through one revolution in use. Zero degrees corresponds to the spoke being between the hub and the ground (i.e., at the six o'clock position). 50 -50 -100 -150 -200 -250 -300 -150 -100 -50 50 100 150 Spoke position in degrees He, microstrain