A body is subjected to uniaxial tensile stress of 20 MPa in the y-direction as well as a temperature decrease of 10 degrees K. The material's elastic modulus is 90 GPa, the Poisson's ratio is 0.20, and the coefficient of thermal expansion is 12E-6 per degree K. What are the normal strains in the x, y, and z directions (microstrain units) ? Exx —102, € yу — 51, YY Ezz 82 -164, E yy –164, Exx = Ezz = -164 -164, E yy 102, Exx = Ezz = -164 164, Eyy - 102, Exx

A body is subjected to uniaxial tensile stress of 20 MPa in the y-direction as well as a temperature decrease of 10 degrees K. The material's elastic modulus is 90 GPa, the Poisson's ratio is 0.20, and the coefficient of thermal expansion is 12E-6 per degree K. What are the normal strains in the x, y, and z directions (microstrain units) ? Exx —102, € yу — 51, YY Ezz 82 -164, E yy –164, Exx = Ezz = -164 -164, E yy 102, Exx = Ezz = -164 164, Eyy - 102, Exx

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can you please answer question B, thank you
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] pipe is subjected to a tensile load P. The pipe has an outside diameter of D = 280 mm, a cross-sectional area of A = 7550 mm², and a length of L = 9.5 m. The initial longitudinal normal strain in the pipe is zero. After load P is applied and the temperature of the pipe has been increased by AT = 40°C, the longitudinal normal strain in the pipe is found to be 2260 με. Calculate the magnitude of load P. Answer: P = M. L kN D P
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 270 mm, a cross-sectional area of A = 13520 mm², and a length of L = 4.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1830 με. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. P Answer: Δd = i d eTextbook and Media Save for Later L mm Attempts: 0 of 5 used Submit Answer
1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N. The wire is made of a copper alloy having a stress- strain relationship that may be described mathemat- ically by 124,020ɛ 0 s8s 0.03 (o = MPa) 1+ 300ɛ in which e is nondimensional and o has units of MPa. (a) Construct a stress-strain diagram for the material. (b) Determine the elongation of the wire due to the forces P. (c) If the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
The principal plane stresses and associated strains in a 35 ksi, 02 = 15 ksi, plane at a point are 01 1 €1 = 1.02(10-3), 2 = 0.180(10-³). ▼ Determine the modulus of elasticity. Express your answer using three significant figures and include the appropriate units. E= Submit Part B V= μA Value Request Answer Submit Determine the Poisson's ratio. Express your answer using three significant figures. ΠΑΠΙ ΑΣΦ | Η VE Units Request Answer ? vec POSSIA space ?
A 45° strain gauge rosette placed on a stainless steel structure results in the following values being determined for the maximum and minimum principal strains: €1 = 1,625.9 ×10–6 and €2 = -753.4 x10-6. Assuming plane stess, determine the factor of safety against the Tresca criterion. For stainless steel, use Young's modulus E = 196 GPa, Poisson's ratio v = 0.29 and yield stress oy = 1120 M Pa. Give your answer to 2 decimal places.
Calculate the Modulus of elasticity, Modulus of toughness and Modulus of Resilience for the material from stress-strain diagram below.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
Eyy Yxy 1 Exa 1 Figura 1: Problema 1
If the engineering strain in a tensile bar is 0.0025 and Poisson’s ratio is 0.33, find the original length and the original diameter if the length and diameter under load are 2.333 ft. and 1.005 in. respectively.
5. Consider a cylindrical specimen of a steel alloy (Figure 6.22) 10 mm in diameter and 75 mm long that is pulled in tension. Determine its elongation when a load of 20,000 N is applied. Stress (MPa) 600 500 400 300 200 100 0 0.00 0.04 Stress (MPa) 500 400 300 200 100 0.000 0.002 0.004 0.006 0.08 Strain Strain 0.12 0.16 0.20 Figure 6.22 Tensile stress-strain behavior for a steel alloy.