A bar having a length of 125 mm and cross-sectional area of 467.5 mm² is subjected to an axial force of 40 kN as shown in (Figure 1). Part A If the bar stretches 0.03 mm, determine the modulus of elasticity of the material. The material has linear-elastic behavior. Express your answer to three significant figures and include the appropriate units.

A bar having a length of 125 mm and cross-sectional area of 467.5 mm² is subjected to an axial force of 40 kN as shown in (Figure 1). Part A If the bar stretches 0.03 mm, determine the modulus of elasticity of the material. The material has linear-elastic behavior. Express your answer to three significant figures and include the appropriate units.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 21 kN without stretching more than 4 mm.
PLEASE ANSWER NUMBER 3.MECH 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
2. A wire is stretched between 2 rigid posts separated by a distance L. If the surrounding temperature changes from T₁ to T₂ with T₂ 0? Or is AF < 0? How does Young's modulus of elasticity figure in your analysis? Explain.
An aluminium alloy rod of length 1.8m and rectangular cross-sectional of area 250mm^2 is subjected to a compressive load of 45kN. Young's modulus and Poisson's ratio for the material are: E = 71 GPa and v =0.33. Determine the decrease in length and increase in area of the bar.
A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. P force and elongation of the rod when this force is applied is below the elasticity of the material, taking as the values given opposite your names in the table presented Calculate the modulus E and the shear modulus G. Take the Poisson's ratio () 0.3. P (N) δ(mm) :500 1,6
Parvinbhai
Question 2 Consider the bar in figure 2, it has cross sectional area A 1.10-4m², modulus of elasticity E = = 200GPa, and length 1.5 m. The bar is fixed to a wall on its left hand side, and has a constant loading of 1(x) = −10 kN/m applied along its length. x=0.0 |(x) = -10 kN/m 1.5 m X x=1.5 Figure 2: diagram of bar subject to applied force along its length a) The displacement of the bar u(x) is governed by the equation ə du(x) AE dx dx +1(x) 0 x = [0, 1.5], state the two boundary conditions for this bar problem, and give a short reasoning for your answer (maximum 2 sentences for each boundary condition).
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 660 mm2. If the stress in the bar must not exceed 290 MPa and the maximum deformation in the bar must not exceed 10 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 7 m, b = 4.2 m, and c = 9.1 m.
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
A steel [E = 200 GPa] rod with a circular cross section is 5 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 55 kN without exceeding an allowable stress of 180 MPa. State your answer in mm without including the units, and correct to two decimal places. Answer:
A steel column is a cylinder 6.8 m long and 0.35 m in diameter. What is the change in length of the column when it experiences a tensile stress resulting from the application of a 3600 N force? The elastic modulus for steel is 20 × 1010 Nm2/kg2. ΔL = m
The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure below (Figure 1). The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.5 mm. Take v=0.35 Figure σ (MPa) 490 0.007 € (mm/mm) Part A If a load of P = 40 kN is applied to the specimen, determine its new diameter. Express your answer to four significant figures and include appropriate units. d= Submit Part B L= O Value Submit μA Request Answer Determine its length. Express your answer to four significant figures and include appropriate units. Provide Feedback Value Units Request Answer ? Units ?