Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ L2 A Aluminum B (2) Copper CP

Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ L2 A Aluminum B (2) Copper CP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
Problem 1 A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 × 10° psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. Note provide a diagram/figure.
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
3. A 1.40 m long steel circular bar is acted upon by forces as shown in fig below. determine the total elongation of the bar. Take E steel=200Gpa and E brass = 85GN/m² 4 cm 3 cm 3 cm 40 kN 60 kN Steel 100 kN 80 kN Steel Brass 40 cm 60 cm 40 cm
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
4 m B 4m 8 0.4 m AB X-Section 0.2 mIO (a) Determine to that results in the gap (8) being closed. (b) If w=628 kN/m, determine the internal force in member BC? BC X-Section For the bar shown above, a uniformly distributed axial load wo (force per unit length) is applied between A and B. The diameter of the cross sections AB and BC are also indicated. The material properties of the bar are: E= 20 GPa and 0.3. If the gap 61 mm, then answer the following questions (you can take a 3.14):
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με
2. A compound bar of length 500 mm consists of a strip of aluminium 50 mm wide and 25 mm thick and a strip of steel 65 mm wide x 20 mm thick rigidly joined at the ends. If elastic modulus of aluminium and steel are 1 × 105 N/mm² and 2 × 105 N/mm², calculate the stresses developed in each material and the extension of the compound bar when axial tensile force of 60 kN acts.
1
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.1 lb/in.³ is the specific weight of the material, y = 2.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 5 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) 8 = i (b) avg (c) Emax = i x10 in. με με