The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of materials. E1 = 70 Gpa and E2 = 210 Gpa. P = 100 kN axial compressive force It affects the C point. The diameter of the circular bars is D1 = 80 mm, D2 = 40 mm and their length L1 = 20 cm. and L2 = 30 cm. (The direction of the force P is in the negative x-axis direction.) a) What are the displacements at B and C points? b) What is the reaction force at point A? c) What are the stresses in the bar?

Q: A horizontal boom 11.5 M in length, AE is supported by guy wires from A to B,C and D. If the tensile…

A: Given: Fad = 360kN Resultant is horizontal at A To find: Tension in wires AB,AC and resultant

Q: Question 2) The Russell fracture traction device and a mechanical model of the leg are shown in the…

A: L = 100 cmW = 250 NIt is asked to find the tension T1, T2

Q: 2.) The plate is supported by a pin in a smooth slot at B. What are the reactions at the supports?…

A: Given:The diagram of the problem is given below;

Q: Snap fits are commonly used to lock plastic parts together. A design for a torsional snap- fit is…

A: Part(a).Suppose,The resistive torque at A is TA.The value of total rotation at c is zero.

Q: Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor…

A: W=28lb α = 22° β = 40°diameter1=30milsdiameter2=35mils1mil=0.001in To-Find:-  a) Tensile stresses σ1…

Q: A vertical bar consists of three prismatic segments A|, A" and A3 with cross-sectional areas of 6000…

A: It is not possible to estimate a structural member's ability to bear a load only based on the…

Q: The arm in the figure below weighs 37.6 N. The force of gravity acting on the arm acts through point…

A: The weight of the arms act at A. Taking the moment of the forces about point O,

Q: *3-32. The block is made of titanium Ti-6A1-4V and is subjected to a shortening of 0.06 in. along…

A:

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a = 2 ft • b= 4 ft c= 1 ft then, what…

A: Consider the free body diagram of member AC, Here,

Q: The arm in the figure below weighs 38.0 N. The force of gravity acting on the arm acts through point…

A:

Q: 2) The bar shown has a cross-sectional area of 0.001 m² and a modulus of elasticity of 100 GPa. It…

A: The cross sectional area is .The modulus of elasticity is .The axial uniformly distributed load is…

Q: The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to…

A: Given: To find: Resultant shear force at C in y direction Resultant shear force at C in z…

Q: 1. Three cubes of side l0, 2l0, and 3l0, are placed next to another (in contact) with their centers…

A: 1.a) Position of the centre of the mass from the left side is 3.83l0. b) New mass density would be…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.