A 16-mm-diameter steel [E= 200 GPa] rod (2) is connected to a 50-mm-wide by 8-mm-thick rectangular aluminum [E= 70 GPa] bar (1). Determine the force Pr

Q: d AB (G= 39 GPa). Eac

A: answer= 17.899 deg

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or  tensile or…

Q: 1.4 (A). Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and…

A:

Q: In the hanger shown, the upper portion of link ABC is 3/8 in. thick, and the lower portions are each…

A:

Q: Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: For the weight and tension in the figure shown, find T1, T2 and T3. Put the final answers for each…

A: Given: W = 600 N   The free-body diagram of the block is given below: Force balance: T1 = W = 600 N

Q: What is the position of the center of mass of the bar, measured as distance x from the bar's left…

A:

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 31300 ksi] bars (1) and (2) are…

A:

Q: Problem # 7: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y…

A:

Q: Two steel wires support a moveable overheadcamera weighing W = 28 lb (see fgure part a) usedfor…

A: W=28lb α = 22° β = 40°diameter1=30milsdiameter2=35mils1mil=0.001in To-Find:-  a) Tensile stresses σ1…

Q: A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 =…

A: According to the given data P1=95kips P2=115kips Diameter = 1.5in For steel E= 29000ksi Length of…

Q: The screw eye in Fig. 2-1la is subjected to two forces, F, and F.. Determine the magnitude and…

A: Given Data F1=100 N F2=150 N

Q: 8 kN C 8 kN В L 45° 45° 60° A E D

A:

Q: 3. When two metal sheets are riveted together by a circular rivet, and two forces that are in the…

A:

Q: A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the bolt.…

A: Given data: The torque required to break the bolt is T = 105 ft-lb. The length of the wrench is l =…

Q: Replace the three forces acting on the shaft by a singl resultant force. Suppose that F1 = 650 lb,…

A:

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, Fy = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: Question The bronze bar 3 m long with a cross-sectional area of 430 mm2 is placed between two rigid…

A:

Q: The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the…

A:

Q: 140 N 80 30 + 26 mm 39 mm - 1. Find the magnitude of force "F" and, 2. the magnitude of the…

A:

Q: QUESTION 2 A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in…

A:

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m).  The…

A:

Q: An aluminum alloy [E = 8400 ksi] pipe with a cross-sectional area of A₁ = 4.20 in.² is connected at…

A:

Q: 2. A pickup tailgate is held horizontal by two cables AB, one at either end. Find the maximum load…

A: Given data weight of tailgate (Wg) = 50 lbs  the load limit of cables (T) = 250 lbs all other…

Q: mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the…

A: From the given data:

Q: A 1.50-in.-diameter brass [G = 5800 ksi] rod is used as a shaft. Determine the thickness of hollow…

A: d=1.50 in Gbrass=5800 ksi Gsteel=11200 ksi τmax=7200 psi τmin=9600 psi

Q: The connection shown consist of five steel plates joined by a steel bolt with a diameter of 6 mm.…

A: The given information in the problem is shown in the following attached image:

Q: A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and…

A: Answer: The single uniformly distributed load in x-direction that would produce the same deformation…

Q: L,=40mm; L,= 120mm; L,=80mm L=100mm and 0,=65°. Find the possible value of 0, and and 0,

A:

Q: A small aluminum alloy [E = 75 GPa] tee shape is used as a simply supported beam as shown. For this…

A:

Q: Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they are…

A: Given: Total force transmit; FT =50*103 KN  Force in one fork; F =25*103 KN diameter of pin; d =…

Q: You are designing a 1/4 inch diameter pin with a yield strength of 50,000 psi to hold 1000 lbf. You…

A: In case of tension and double shear the failure will be at the same time. Generally, the yield…

Q: Consider the frame shown in (Figure 1). Suppose that F₁ = 26 kN. Part A Determine the x and y…

A:

Q: F1 F2 a F3 A F4 F5 Consider the following values: - a - 25 m; b - 5 m; a - 25 m; d - 5 m; F1 6 KN;…

A:

Q: 10 b 15 in. 15 in. poccor D 30° 10 b TO P

A: To findWhat is the minimum tension P of the cord?What is the orientation, ?Given     the resultant…

Q: 2-1. A standard steel specimen of Į in. dia- meter elongated 0.0087 in. in an 8 in. gage length when…

A: Given dataDiameter of the steel specimen d=0.5inElongation of the steel specimen e = 0.0087inGauge…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

A:

Q: A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm diameter…

A: Given: A bar ABCD consists of three sections: AB is 25 mm square and 50 mm long, BC is of 20 mm…

Q: n H hydraulic cylinder AB

A: P=737Nθ=37 1 Length of LBE and LAB,LBE=4002+1502=427.2mmLAB=100+175+8002+429.22=1156.7mm2 Angles,tan…

Q: OD Front view -6 m 18 mm Side view L 120 mm

A:

Q: A two-bar system has the configuration shown in the Figure Q1 below. The cross-sectional area for…

A:

Q: PROBLEM 4. A piece of rubber, which was originally a square shape, has been deformed into a shape…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.